Make sure this part fits

GM 25787947
Drive Shaft

2004-2012 GM

Customer Questions & Expert Answers (15)
GM 25787947 Drive Shaft
GM 25787947 Drive Shaft
  • Part Description
    Shaft Assembly-Propeller; Driveshaft
  • Replaces
    15116624
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2004-2012 Chevrolet ColoradoBase, LS, LT, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
    2004-2012 GMC CanyonSL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 25787947 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 25787947 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after placing the transmission in neutral for the 2007 Chevrolet Colorado? Posted by Customer
    A:
    Raise and support the vehicle, then mark the rear universal joint to the drive shaft flange.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What is the next step after marking the rear universal joint for the 2009 Chevrolet Colorado? Posted by Customer
    A:
    Remove the retaining bolts and clamps, followed by the propeller shaft from the pinion drive flange and the transmission/transfer case.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What should be done after removing the rear propeller shaft for the 2005 Chevrolet Colorado? Posted by Customer
    A:
    Remove the mounting bolts for the center bearing and take the center bearing out from the crossmember, followed by removing the propeller shaft from the transmission.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    How do you mark the rear universal joint for the 2008 Chevrolet Colorado? Posted by Customer
    A:
    Mark the rear universal joint to the drive shaft flange.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What should be done after tightening the bolts for the front propeller U-joint clamps for the 2007 Chevrolet Colorado? Posted by Customer
    A:
    Lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What is the first step to replace the two-piece propeller shaft for the 2010 Chevrolet Colorado? Posted by Customer
    A:
    Place the transmission in neutral and release the park brake if it is applied.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    How can you prevent separation of the front U-joint bearing caps for the 2006 Chevrolet Colorado? Posted by Customer
    A:
    Wrap them with tape or a rubber band.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What needs to be removed to detach the rear propeller shaft for the 2009 Chevrolet Colorado? Posted by Customer
    A:
    Remove the clamps and retaining bolts for the rear propeller shaft at the pinion drive flange and the center bearing.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What is the first step in the installation process for the 2010 GMC Canyon? Posted by Customer
    A:
    Remove the tape or rubber band from the U-Joint.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    How do you remove the rear propeller shaft for the 2007 GMC Canyon? Posted by Customer
    A:
    Remove the rear propeller shaft from the center bearing, followed by the mounting bolts for the center bearing, and then take out the center bearing from the crossmember. Finally, remove the propeller shaft from the transmission.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    How tight should the retaining bolts be when first installed for the 2008 GMC Canyon? Posted by Customer
    A:
    Only finger tight to hold the front propeller shaft in position.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What is the first step in the installation process for the 2008 GMC Canyon? Posted by Customer
    A:
    Align the reference marks on the propeller shaft to the transmission and install the propeller shaft in the transmission.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    How should the front propeller shaft be handled after removal for the 2009 GMC Canyon? Posted by Customer
    A:
    Wrap the front U-joint bearing caps with tape or a rubber band to prevent separation.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What should be done after tightening the bolts for the front propeller U-joint clamps for the 2010 GMC Canyon? Posted by Customer
    A:
    Lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Drive Shaft 25787947 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 25787947 Drive Shaft is available in the market under the name GM Drive Shaft. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 25787947 Drive Shaft fits certain Chevrolet Colorado models, as well as GMC Canyon models.
The original GM component designated by manufacturer part number 25787947 maintains top performance when functioning as the Shaft Assembly-Propeller; Driveshaft unit. The component 25787947 is constructed from durable material and its dimensions span 65.3 x 4.1 x 4.1 inches while weighing 15.60 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Shaft, Propeller. The part 25787947 has available replacement options 15116624. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.