Make sure this part fits

GM 25768320
Lower Control Arm, Rear Driver Side

2004-2009 Cadillac SRX

Customer Questions & Expert Answers (12)
GM 25768320 Lower Control Arm, Rear Driver Side
  • Part Description
    Arm, Rear Axle Control Arm
  • Position
    Rear Driver Side
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine GM
    Manufacturer Part Number25768320
    Part DescriptionArm, Rear Axle Control Arm
    Other NamesControl Arm
    Item Weight2.40 Pounds
    PositionRear Driver Side
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU25768320
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California's Proposition 65
  • Vehicle Fitment

    Year Make Model Trim Engine
    2004-2009 Cadillac SRXBase6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 25768320 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 25768320 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after removing the air deflector and shock module yoke for the 2009 Cadillac SRX? Posted by Customer
    A:
    Remove the stabilizer shaft link lower retaining nut and detach the stabilizer shaft link from the lower control arm.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What is the torque specification for the power steering gear retaining bolts for the 2006 Cadillac SRX? Posted by Customer
    A:
    120 Nm (89 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What should be done after securing the lower control arm to the cradle for the 2007 Cadillac SRX? Posted by Customer
    A:
    Tighten the power steering gear retaining bolts to 120 N.m (89 lb ft), then install the lower control arm to steering knuckle nut, tightening it to 20 N.m (15 lb ft) plus an additional 210 degrees.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What should be done after removing the jack for the 2007 Cadillac SRX? Posted by Customer
    A:
    Support the frame with a suitable jack and remove the front bolts from the frame to lower the front of the rear frame.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Trailing Arm
    Q:
    What should be removed next after the tire and wheel for the 2004 Cadillac SRX? Posted by Customer
    A:
    Remove the upper control arm to knuckle retaining nut.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What are the torque specifications for tightening the bolts for the 2008 Cadillac SRX? Posted by Customer
    A:
    Lower control arm to frame bolt to 135 N.m (100 lb ft), lower control arm to frame nut to 135 N.m (100 lb ft), and lower control arm to knuckle bolt to 160 N.m (118 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What are the final steps after securing the brake pipe bracket for the 2008 Cadillac SRX? Posted by Customer
    A:
    Attach the automatic level control link to the upper control arm, reinstall the tire and wheel, and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Trailing Arm
    Q:
    What should be done after removing the jack for the 2006 Cadillac SRX? Posted by Customer
    A:
    Support the frame with a suitable jack and remove the front bolts from the frame to lower the front of the rear frame.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Trailing Arm
    Q:
    How should the trailing link be installed for the 2009 Cadillac SRX? Posted by Customer
    A:
    Begin by loosely installing the trailing link to the vehicle, followed by the trailing link to frame bolt and nut.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Trailing Arm
    Q:
    What is the first step to replace the upper control arm for the 2009 Cadillac SRX? Posted by Customer
    A:
    First, raise and support the vehicle, then remove the tire and wheel.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What needs to be removed after supporting the lower control arm for the 2004 Cadillac SRX? Posted by Customer
    A:
    Remove the trailing link to knuckle nut and bolt.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Trailing Arm
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM 25768320, Excellent Performance and Perfect Fitment

To ensure reliability, purchase GM part # 25768320 Lower Control Arm, Rear Driver Side. It is sometimes referred to as GM Control Arm, GM Trailing Arm. Choosing OEM parts is the optimal decision for guaranteeing superior quality and perfect performance. These components undergo stringent quality checks and are carefully constructed to comply with GM's factory specifications, ensuring a smooth installation process.

ChevyPartsGiant.com is a leading supplier of genuine GM parts such as GM 25768320 Lower Control Arm, Rear Driver Side. Our website boasts an extensive inventory of OEM GM parts, available at highly competitive prices in the market. Should you require any new genuine GM parts, rest assured we will deliver them swiftly and efficiently to your doorstep. Furthermore, all our parts come with the assurance of a manufacturer's warranty. For detailed Cadillac parts information, click here.
Choose ChevyPartsGiant for discounted prices, exceptional service and fast delivery