Make sure this part fits

GM 10334474
Mount Bracket

2004-2008 GM

Customer Questions & Expert Answers (18)
GM 10334474 Mount Bracket
  • Part Description
    Bracket-Engine Mount; Engine Mount Bracket; Motor Mount
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2005-2008 Buick LaCrosseCXS6 Cyl 3.6 L GAS
    2004-2006 Buick RendezvousCX, CXL, CXL Plus, Ultra6 Cyl 3.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 10334474 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 10334474 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the next step after lowering the engine for the 2007 Buick LaCrosse? Posted by Customer
    A:
    Install the engine mount lower nuts and tighten them to 47 N.m (35 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the first step to replace the right engine mount bracket for the 2005 Buick LaCrosse? Posted by Customer
    A:
    First, remove the engine mount and the upper nuts from the engine mount.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What needs to be detached from the engine right side exhaust manifold for the 2005 Buick LaCrosse? Posted by Customer
    A:
    The three-way catalytic converter pipe.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the final step in the process for the 2008 Buick LaCrosse? Posted by Customer
    A:
    Reinstall the engine mount.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What should be removed after raising for the 2008 Buick LaCrosse? Posted by Customer
    A:
    Remove the left tire and wheel assembly, followed by the left inner splash shield.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the final step after installing the engine mount bracket for the 2006 Buick LaCrosse? Posted by Customer
    A:
    Finally, reinstall the engine mount.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What are the final steps after tightening the upper nuts for the 2005 Buick LaCrosse? Posted by Customer
    A:
    Remove the transmission jack, reinstall the left inner splash shield, put back the left wheel and tire assembly, and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be done after removing the upper nuts for the 2006 Buick LaCrosse? Posted by Customer
    A:
    Carefully raise the transaxle assembly and remove the transaxle mount lower nuts (NPN 116) from the frame.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    How should the engine be raised for the 2008 Buick LaCrosse? Posted by Customer
    A:
    Use a utility stand and a block of wood.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What should be done after installing the engine mount upper nuts for the 2006 Buick LaCrosse? Posted by Customer
    A:
    Attach the engine mount bracket with the engine mount to the oil pan and hand-tighten all the engine mount bracket bolts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the first step to replace the right side engine mount bracket for the 2007 Buick LaCrosse? Posted by Customer
    A:
    First, remove the engine mount and the upper nuts from the engine mount.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What should be done after removing the engine mount for the 2004 Buick Rendezvous? Posted by Customer
    A:
    Next, detach the engine mount bracket from the engine mount.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What is the first step to inspect the transmission mount for the 2006 Buick Rendezvous? Posted by Customer
    A:
    Insert a block of wood that spans the width of the oil pan bottom between the oil pan and the jack support to prevent oil pan damage and possible engine failure.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be done after attaching the engine mount bracket for the 2005 Buick Rendezvous? Posted by Customer
    A:
    Tighten the engine mount bracket bolts to 58 Nm (43 ft. lbs.) for FWD, or hand tighten for AWD.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the next step after fitting the studs into the bracket for the 2007 Buick LaCrosse? Posted by Customer
    A:
    Install the transaxle mount upper nuts (NPN 1151) and tighten them to 47 N.m (35 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What are the final steps after tightening the lower nuts for the 2006 Buick Rendezvous? Posted by Customer
    A:
    Reinstall the right engine splash shield, right front wheel and tire, catalytic converter, engine mount struts, and air cleaner outlet duct.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    Is there any precaution to consider during installation for the 2005 Buick Rendezvous? Posted by Customer
    A:
    Yes, adhere to the Fastener Notice in Service Precautions.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Mount Bracket 10334474 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 10334474 Mount Bracket is available in the market under the name GM Engine Mount, Motor And Transmission Mount, Engine Mount Bracket. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 10334474 Mount Bracket fits certain Buick LaCrosse, Rendezvous models.
The original GM component designated by manufacturer part number 10334474 maintains top performance when functioning as the Bracket-Engine Mount; Engine Mount Bracket; Motor Mount unit. The component 10334474 is constructed from durable material and its dimensions span 10.8 x 4.9 x 2.1 inches while weighing 1.80 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Lower Bracket; Bracket, Engine Mounting. The part 10334474 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.