Make sure this part fits

GM 88964135
Overhaul Kit

2005-2011 GM

Customer Questions & Expert Answers (16)
GM 88964135 Overhaul Kit
  • Part Description
    Caliper Kit, Rear Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit
  • Position
    Rear
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2006-2011 Buick LucerneCX, CXL, CXL Special Edition, CXS, Super6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS
    2005-2007 Buick TerrazaCX, CXL6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    2006-2011 Cadillac DTSBase, Livery, Luxury, Platinum, Premium8 Cyl 4.6 L GAS
    2005-2008 Chevrolet UplanderBase, LS, LT6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    2005-2006 Pontiac MontanaSV66 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
    2005-2007 Saturn Relay1, 2, 36 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is 88964135 compatible with my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 88964135 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done if a piston fails to be removed for the 2006 Buick Lucerne? Posted by Customer
    A:
    Reposition the removed piston back into the caliper, use a small block of wood and a C-clamp to partially seat it, then apply air again.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the final step after installing the brake caliper for the 2006 Buick Lucerne? Posted by Customer
    A:
    Install the brake caliper to the vehicle and inspect for leaks during the hydraulic brake system bleeding procedure. If leaks occur, replace the caliper piston assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done to test the brake system for the 2005 Buick Terraza? Posted by Customer
    A:
    Apply approximately 778 Nm (175 ft. lbs.) of force to the brake pedal for ten seconds and inspect the brake caliper and hydraulic brake system for leaks.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be inspected on the brake caliper piston for the 2005 Buick Terraza? Posted by Customer
    A:
    Inspect for scoring, nicks, corrosion, or worn chrome plating, and replace it if any issues are found.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after inspecting the fluid level for the 2007 Buick Terraza? Posted by Customer
    A:
    Raise and support the vehicle, then remove the tire and wheel assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How do you compress the caliper pistons for the 2008 Cadillac DTS? Posted by Customer
    A:
    Use a large C-clamp over the brake caliper body, tightening it until the caliper pistons are compressed enough to slide past the brake rotor, then remove the C-clamp.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the next step after inspecting the fluid level for the 2007 Cadillac DTS? Posted by Customer
    A:
    Raise and support the vehicle, then mark the relationship of the wheel to the axle flange and remove the tire and wheel assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the next step after removing the brake hose for the 2010 Cadillac DTS? Posted by Customer
    A:
    Remove the brake caliper pin bolts and take off the brake caliper.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the next step after removing the brake hose for the 2006 Cadillac DTS? Posted by Customer
    A:
    Remove the brake caliper pin bolts and take off the brake caliper.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How should the parts be cleaned for the 2006 Buick Terraza? Posted by Customer
    A:
    Clean all parts with denatured alcohol and dry them with filtered, non-lubricated compressed air.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after compressing the caliper pistons for the 2009 Cadillac DTS? Posted by Customer
    A:
    Remove the C-clamp and detach the brake hose to caliper bolt, discarding the two copper brake hose gaskets.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What are the final steps after reassembling the brake components for the 2008 Chevrolet Uplander? Posted by Customer
    A:
    Remove the nuts securing the rotor to the hub, install the tire and wheel, lower the vehicle, fill the master cylinder to the proper level, and bleed the brake system.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the procedure for installation for the 2006 Chevrolet Uplander? Posted by Customer
    A:
    Ensure the caliper bolt boots are properly installed, then attach the caliper to the caliper bracket and tighten the brake caliper bolts to 54 Nm (40 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after inspecting the fluid level for the 2008 Chevrolet Uplander? Posted by Customer
    A:
    Raise and support the vehicle, then remove the tire and wheel assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after bleeding the brake system for the 2005 Chevrolet Uplander? Posted by Customer
    A:
    Adjust the park brake system, reinstall the tire and wheel assembly, and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Overhaul Kit 88964135 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 88964135 Overhaul Kit is available in the market under the name GM Brake Caliper Repair Kit, Brake Calipers. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 88964135 Overhaul Kit fits certain Chevrolet Uplander models, as well as Cadillac DTS. Additionally, it is compatible with Buick Lucerne, Terraza and Pontiac Montana models.
The original GM component designated by manufacturer part number 88964135 maintains top performance when functioning as the Caliper Kit, Rear Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit unit at its Rear. The component 88964135 is constructed from durable material and its dimensions span 2.1 x 2.0 x 2.1 inches while weighing 0.40 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Caliper Overhaul Kit; Caliper Kit, Wheel Brake Cylinder/Caliper Piston; Caliper Kit, Wheel Cylinder Piston. The part 88964135 has available replacement options. Each vehicle needs 2 units of the part marked as SKU 88964135. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.