Other Name: Actuator, Air Conditioner Control; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Mode Motor; Actuator; Actuator, A/C Control; Motor, A/C Control
Fits the following Buick Models:
Lucerne | 2006-2011 | CX, CXL, CXL Special Edition, CXS, Super | 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS
Other Name: Actuator, Air Conditioner Control; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator, A/C Vacuum Control; Actuator, A/C Control
Fits the following Buick Models:
Terraza | 2005-2007 | CX, CXL | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
Other Name: Actuator, Air Conditioner Control; HVAC Heater Blend Door Actuator; Temperature Door Actuator; Link; Lever; Actuator; Actuator, A/C Control
Fits the following Buick Models:
Enclave | 2018-2024 | Avenir, Base, Essence, Preferred, Premium | 6 Cyl 3.6 L GAS
| Page 1 of 4 |Next >
1-20 of 64 Results
Buick Blend Door Actuator Parts Questions & Experts Answers
Q: How to replace the LH Blend Door Actuator on Buick LeSabre?
A: To replace the left air temperature actuator, one should begin with removal of the left side sound insulator, removal of knee bolster and Instrument Panel Module (IPM). Before you remove the actuator of air temperature, remove the retaining screws and disconnect the electrical connector from the air temperature actuator. For installation, place the new air temperature actuator and mount the driver air throughput retaining screws with a tightening stringency of 1.4 N.m (12 lb in). Replace the electrical connector back to actuator, re-install the IPM, knee bolster, and left side sound insulator. Finally, recalibrate the actuator.
Q: How to replace the Blend Door Actuator on the right side on Buick LaCrosse?
A: Start the right-side air temperature actuator replacement process by removing two components: the right side instrument panel (I/P) insulator followed by the I/P compartment. First remove all screws securing the air temperature actuator before disconnecting its electrical connector. Take out the actuator from its assembly position within the HVAC system. During installation use the air temperature actuator and locate its slots on the electric actuator driver to match the shaft flats while also setting the locating hole to align with the HVAC module case alignment pin. Position and slide the actuator driver along the shaft so both the driver and the HVAC module case mounting holes reach perfect alignment. Install screws to the air temperature actuator while tightening them to achieve 1.5 N.m (13 lb in) torque before reconnecting the electrical connector. Put the I/P compartment back into position followed by installation of the right side I/P insulator. Finally, calibrate the actuator.
Q: How to service and repair the Blend Door Actuator on Buick Regal?
A: To service and repair the air door actuator / motor, begin by removing the right instrument panel insulator panel and the ip compartment to be removed. Release the two vacuum lines the defroster actuator and tighten the orange vacuum line to the recirculation actuator then install a hand Vacuum Pump. In its attachment to the hvac module case, remove the defroster actuator. If ease of access is affecting you, then it is renown to use the hand Vacuum Pump to fully open the recirculation actuator door, rotate the defroster actuator to the right and up into the space where it would blend with the back of the dash and the hvc module. Modify the defroster actuator from defroster door arm. For the installation of the device, fix the defroster actuator on the arm of the defroster door and snap it into the number of the hvac module. Attached the vacuum line to the actuator, removed hand Vacuum Pump , reattached vacuum line to the recirculation actuator. Finally, reinstall the i/p compartment and the right instrument insulator panel.