Other Name: Handle Assembly-Front Side Door Inside *Titanium; Handle, Door Lock Remote Control Inside
Position: Front Passenger Side
Replaces: 15908335, 15935956
Fits the following GMC Models:
Sierra 1500 | 2007-2013 | Denali, Hybrid, SL, SLE, SLT, WT, XFE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
Sierra 2500 HD | 2007-2014 | Denali, SLE, SLT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
Sierra 3500 HD | 2007-2014 | Denali, SLE, SLT, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
Yukon | 2007-2014 | Denali, Denali Hybrid, Hybrid, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
Yukon XL 1500 | 2007-2014 | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
Yukon XL 2500 | 2007-2013 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
Q: How to replace the front inside door handle on GMC Canyon?
A: The first step to replace the front inside door handle consists of removing the front door trim panel and the water deflector. Release the retaining tabs from the door inner panel using the inside door handle by sliding it back prior to separating the cables that secure the lock from the inside door handle and extracting the handle. You should first connect the lock cables to the inside door handle then insert the retaining tabs into the slots on the door inner panel before moving the handle forward to lock the retainers. Place the front door trim panel and water deflector in their appropriate positions last.
Q: How to replace the front interior door handle on GMC Sierra 1500?
A: Start by removing the trim panel followed by the inside door handle mounting bolts in order to replace the front door interior handle. The inside door handle requires sliding towards the front to separate from the door while you disconnect the control rod from the handle before removing the assembly. You should connect the control rod to the inside door handle and put the handle in position following the Fastener Notice in Service Precautions. Fasten the two inside door handle retaining bolts with torque setting at 9 N.m (80 lb in) before putting back the trim panel.
Q: How to replace the rear side inner door handle on GMC Yukon?
A: The first step of replacing the rear side door inside handle begins with pulling the door trim panel from the door and supporting its bottom edge on door panel hooks. Remove the rear side door inside handle fasteners followed by disconnection of the fasteners assembly. Start by disconnecting the electrical connector before depressing both tabs to remove the rear side door cable and slowly draw the cable from the handle assembly. During installation the rear side door cable requires connection while fully seating past the guide tab. Add the rear side door inside handle assembly by sliding it into position. Insert and tighten the fasteners holding the rear side door inside handle at 2 nm (18 lb in). Metro installs the door trim panel as the last step.