Make sure this part fits

GM 15212141
Drive Shaft, Front

2004-2014 GM

Customer Questions & Expert Answers (19)
GM 15212141 Drive Shaft, Front
  • Part Description
    Shaft Assembly-Front Axle Propeller; Driveshaft
  • Position
    Front
  • Manufacturer
    General Motors
Make sure this part fits
$915.16 MSRP: $1209.41
You Save: $294.25 (25%)
1
ADD TO CART
  • Vehicle Fitment

    Year Make Model Trim Engine
    2008-2014 Cadillac CTSBase, Luxury, Performance, Premium6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
    2004-2009 Cadillac SRXBase6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
    2005-2011 Cadillac STSBase, Platinum, V6 Cyl 3.6 L GAS, 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 15212141 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 15212141 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be reinstalled after securing the propeller shaft for the 2010 Cadillac CTS? Posted by Customer
    A:
    Reinstall the front drive axle heat shield, the right catalytic converter, and the lower engine shield.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    How should the propeller shaft be supported during removal for the 2009 Cadillac CTS? Posted by Customer
    A:
    Support the propeller shaft at the center support bearing with a jack stand.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What is the first step to replace the rear propeller shaft with MX7 or MN6 for the 2010 Cadillac CTS? Posted by Customer
    A:
    First, raise and support the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What lubricant should be applied to the rear propeller shaft centering bushing for the 2008 Cadillac CTS? Posted by Customer
    A:
    GM P/N 1051344 (Canadian P/N 993037).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What is the final step after reinstallation for the 2008 Cadillac CTS? Posted by Customer
    A:
    Remove the support and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What is the next step after releasing the CV joint for the 2006 Cadillac SRX? Posted by Customer
    A:
    Lower the support device and move the propeller shaft forward to detach it from the differential flange, then remove the propeller shaft from the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What is the next step after releasing the CV joint from the differential pinion flange for the 2007 Cadillac SRX? Posted by Customer
    A:
    Remove the CV joint-to-transfer case flange bolts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What is the final step after installation for the 2008 Cadillac STS? Posted by Customer
    A:
    Reinstall the propeller shaft heat shield and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What should be done after raising the 2009 Cadillac STS? Posted by Customer
    A:
    Remove the propeller shaft heat shield and mark the location of the propeller shaft constant velocity (CV) joint to the transfer case flange.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What should be done with the propeller shaft-to-flange bolts for the 2004 Cadillac SRX? Posted by Customer
    A:
    Inspect them and replace if damaged or worn.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What is the process for installing the front propeller shaft for the 2006 Cadillac STS? Posted by Customer
    A:
    Push the front propeller shaft to the rear, install the coupler to the transmission flange, repeat the cleaning and threadlocker application process, then install the front propeller shaft coupler-to-transmission flange bolts and secure them with washers and nuts, tightening to 85 Nm (63 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What should be inspected on the propeller shaft for the 2005 Cadillac STS? Posted by Customer
    A:
    Inspect for rotational movement between the CV joint and the propeller shaft tube, grease leaks, damage to the CV joints or seals, and binding of either CV joint.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    How do you support the propeller shaft during the replacement process for the 2007 Cadillac SRX? Posted by Customer
    A:
    Use a suitable jack to support the propeller shaft near the support bearing.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What is the first step in the installation process for the 2009 Cadillac SRX? Posted by Customer
    A:
    Ensure the coned end of the propeller shaft CV joint is installed into the transfer case flange.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What should be done before installing the front propeller shaft coupler-to-transfer case flange bolts for the 2010 Cadillac STS? Posted by Customer
    A:
    Clean the threads again and apply threadlocker.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    How should the propeller shaft CV joint to transfer case flange bolts be installed for the 2010 Cadillac STS? Posted by Customer
    A:
    Install the bolts in sequence (1-6) and tighten to 36 Nm (27 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    How should the location of the propeller shaft CV joint be marked for the 2008 Cadillac SRX? Posted by Customer
    A:
    Mark the location of the propeller shaft constant velocity (CV) joint to the transfer case flange.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What should be done to release the CV joint from the differential pinion flange for the 2007 Cadillac STS? Posted by Customer
    A:
    Carefully move the propeller shaft toward the rear of the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Drive Shaft, Front 15212141 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 15212141 Drive Shaft, Front is available in the market under the name GM Drive Shaft. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 15212141 Drive Shaft, Front fits certain Cadillac CTS, SRX, STS models.
The original GM component designated by manufacturer part number 15212141 maintains top performance when functioning as the Shaft Assembly-Front Axle Propeller; Driveshaft unit at its Front. The component 15212141 is constructed from durable material and its dimensions span 5.3 x 5.5 x 42.2 inches while weighing 10.40 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Shaft, Propeller. The part 15212141 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.