Make sure this part fits

GM 25862782
Lower Control Arm, Passenger Side

2004-2014 GM

Customer Questions & Expert Answers (18)
GM 25862782 Lower Control Arm, Passenger Side
GM 25862782 Lower Control Arm, Passenger Side
  • Part Description
    Arm, Steering Knuckle Control Arm and Ball Joint Assembly; Suspension Control Arm Assembly.
  • Position
    Passenger Side
  • Replaces
    15806922, 15921070, 15270102, 25764672, 10399362, 25765777
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2008-2014 Cadillac CTSBase, Luxury, Performance, Premium, V6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
    2004-2009 Cadillac SRXBase6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
    2005-2011 Cadillac STSBase, Platinum6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 25862782 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 25862782 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after removing the tire and wheel for the 2009 Cadillac CTS? Posted by Customer
    A:
    Remove the brake caliper and mounting bracket as an assembly, supporting it with mechanics wire.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What needs to be removed for all-wheel drive for the 2010 Cadillac CTS? Posted by Customer
    A:
    The outer tie rod to the steering knuckle retaining nut.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What is the next step after detaching the upper ball joint for the 2008 Cadillac CTS? Posted by Customer
    A:
    Remove the upper control arm nuts and bolts from the frame, and take the upper control arm out of the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What is the next step after removing the wheel speed sensor for the 2009 Cadillac CTS? Posted by Customer
    A:
    Remove the lower ball joint nut and use the J 43631 (Ball Joint Separator) to detach the ball joint stud from the steering knuckle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What should be removed after disconnecting the stabilizer shaft link for the 2008 Cadillac SRX? Posted by Customer
    A:
    The rear coil spring.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What components need to be reinstalled after the lower control arm installation for the 2008 Cadillac CTS? Posted by Customer
    A:
    Reinstall the wheel speed sensor, stabilizer shaft link, air deflector, and finally the tire and wheel.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What should be done after loosening the power steering gear retaining bolts for the 2007 Cadillac SRX? Posted by Customer
    A:
    Remove the lower control arm to cradle nuts and bolts, then lower the control arm at the frame while moving the ball stud upwards to complete the removal.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What should be done after reattaching the lower control arm to the steering knuckle for the 2009 Cadillac SRX? Posted by Customer
    A:
    Reinstall the ABS wire harness and the stabilizer shaft link, securing the lower retaining nut to 115 Nm (95 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What is the torque specification for the upper control arm to knuckle nut for the 2004 Cadillac SRX? Posted by Customer
    A:
    Tighten to 20 Nm (15 ft. lbs.) plus an additional 210 degrees.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What should be done with the ABS wire harness for the 2009 Cadillac STS? Posted by Customer
    A:
    Carefully remove the ABS wire harness from the lower control arm, ensuring the ball stud does not rotate.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What should be removed after raising for the 2006 Cadillac STS? Posted by Customer
    A:
    The tire and wheel, followed by the shock module yoke.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What is the first step for installation of the new lower control arm for the 2008 Cadillac STS? Posted by Customer
    A:
    Position the new lower control arm and install the cradle bolts, tightening them with the lower control arm at normal vehicle ride height.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What is the torque specification for the lower control arm to steering knuckle nut for the 2006 Cadillac SRX? Posted by Customer
    A:
    40 Nm (30 ft. lbs.) plus an additional 120 degrees.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    How do you install the new lower control arm for the 2010 Cadillac STS? Posted by Customer
    A:
    Position the lower control arm and install the lower control arm to cradle bolts, tightening them with the lower control arm at normal vehicle ride height.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What is the torque specification for the power steering gear retaining bolts for the 2007 Cadillac STS? Posted by Customer
    A:
    Tighten them to 120 N.m (89 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What is the torque specification for the upper control arm to knuckle retaining nut for the 2009 Cadillac SRX? Posted by Customer
    A:
    Tighten it to 20 Nm (15 lb ft) plus an additional 210 degrees.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    Q:
    What tool should be used to disconnect the upper control arm from the knuckle for the 2006 Cadillac STS? Posted by Customer
    A:
    Use the Ball Joint Remover (J 43631).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Lower Control Arm, Passenger Side 25862782 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 25862782 Lower Control Arm, Passenger Side is available in the market under the name GM Control Arm. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 25862782 Lower Control Arm, Passenger Side fits certain Cadillac CTS, SRX, STS models.
The original GM component designated by manufacturer part number 25862782 maintains top performance when functioning as the Arm, Steering Knuckle Control Arm and Ball Joint Assembly; Suspension Control Arm Assembly. unit at its Passenger Side. The component 25862782 is constructed from durable material and its dimensions span 5.7 x 18.9 x 15.9 inches while weighing 14.20 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 25862782 has available replacement options 15806922, 15921070, 15270102, 25764672, 10399362, 25765777. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.