Make sure this part fits

GM 89017809
Intake Manifold

2006-2011 GM

Customer Questions & Expert Answers (17)
GM 89017809 Intake Manifold
  • Part Description
    Manifold, Engine Fuel Intake Manifold
  • Position
    Lower
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2009-2011 Buick LucerneCX, CXL, CXL Special Edition6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    2006-2007 Buick TerrazaCX, CXL6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    2006-2011 Chevrolet Impala50th Anniversary Edition, LS, LT, LTZ, Police6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    2006-2010 Chevrolet MalibuLS, LT, Maxx SS, SS6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
    2006-2007 Chevrolet Monte CarloLS, LT, LTZ6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
    2006-2008 Chevrolet UplanderBase, LS, LT6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    2006-2010 Pontiac G6Base
    2006 Pontiac MontanaSV66 Cyl 3.9 L GAS
    2007-2008 Saturn AuraXE6 Cyl 3.5 L GAS
    2008-2009 Saturn VueXE6 Cyl 3.5 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is 89017809 compatible with my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 89017809 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done with the power steering reservoir and generator brackets for the 2010 Buick Lucerne? Posted by Customer
    A:
    Loosen the power steering reservoir to intake manifold bolt and reposition it, and remove the generator to intake manifold bracket bolt.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What should be done with the upper intake manifold for the 2009 Buick Lucerne? Posted by Customer
    A:
    Take off the intake manifold cover ball stud nut and the upper intake manifold bolts and stud, then separate and remove the upper intake manifold from the lower intake manifold along with the gaskets.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What should be done with the ignition coil bracket and wiring harnesses for the 2006 Buick Terraza? Posted by Customer
    A:
    Install the ignition coil bracket with the coils and the wiring harnesses to their retainers.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    How should the push rods be noted during removal for the 2007 Buick Terraza? Posted by Customer
    A:
    The intake push rods measure 147.51 mm (5.81 in) and the exhaust push rods measure 154.87 mm (6.1 in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What should be installed after connecting the EVAP components for the 2008 Chevrolet Malibu? Posted by Customer
    A:
    Install the throttle body, vacuum brake booster hose, and secure the hose clamp.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What is the final step in the process for the 2006 Chevrolet Malibu? Posted by Customer
    A:
    Install the oil level indicator tube bolt, tightening it to 10 Nm (89 inch lbs.), and reconnect the brake booster hose, purge solenoid tube, and PCV hose before reinstalling the throttle body and air cleaner outlet resonator.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What should be removed from the throttle body for the 2007 Chevrolet Impala? Posted by Customer
    A:
    Remove the throttle body bolts and nuts, the throttle body and gasket, the EVAP canister purge solenoid valve bolt and valve, the MAP sensor bracket bolts, the MAP sensor bracket and sensor, and the ignition coil bracket bolts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What should be removed after disconnecting the battery for the 2010 Chevrolet Impala? Posted by Customer
    A:
    Remove the upper intake manifold, followed by the left and right valve rocker arm covers.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What is the next step after disconnecting the electrical connectors for the 2009 Chevrolet Malibu? Posted by Customer
    A:
    Proceed to remove the intake manifold bolts and nuts, then take out the intake manifold.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What should be inspected and lubricated before installing the fuel injectors for the 2008 Chevrolet Impala? Posted by Customer
    A:
    Inspect the fuel rail, fuel injectors, and fuel injector O-rings for damage, and lubricate the O-rings with engine oil.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What should be done after installing the intake manifold for the 2007 Chevrolet Malibu? Posted by Customer
    A:
    Reattach the engine wiring harness clips to the intake manifold, position the oil level indicator tube, and install the knock sensor electrical connector clip and the oil level indicator tube bolt, tightening it to 10 N.m (89 lb in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What should be done after installing the fuel injector rail bolts for the 2009 Chevrolet Impala? Posted by Customer
    A:
    Reconnect the CMP sensor and ECT electrical connectors, position the fuel injector harness connector bracket, and install the bracket bolt, tightening it to 8 Nm (71 lb in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What should be applied to the intake manifold bolts during installation for the 2006 Chevrolet Monte Carlo? Posted by Customer
    A:
    Apply a band of threadlock GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the threads of the intake manifold bolts (512).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What should be connected after installing the fuel injector rail for the 2008 Chevrolet Uplander? Posted by Customer
    A:
    Connect the CMP sensor electrical connector.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What should be done after removing the upper intake manifold for the 2006 Chevrolet Uplander? Posted by Customer
    A:
    Remove the fuel injector rail, disconnect the heater inlet pipe with heater hose from the lower intake manifold, and reposition it.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What should be done with the intake manifold tuning valve for the 2008 Chevrolet Uplander? Posted by Customer
    A:
    Disconnect the engine harness electrical connector from the intake manifold tuning valve.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Intake Manifold
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Intake Manifold 89017809 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 89017809 Intake Manifold is available in the market under the name GM Intake Manifold. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 89017809 Intake Manifold fits certain Chevrolet Malibu, Impala, Monte Carlo models, as well as Buick Lucerne, Terraza. Additionally, it is compatible with Pontiac G6, Montana and Saturn Vue, Aura models.
The original GM component designated by manufacturer part number 89017809 maintains top performance when functioning as the Manifold, Engine Fuel Intake Manifold unit at its Lower. The component 89017809 is constructed from durable material and its dimensions span 21.2 x 14.6 x 9.2 inches while weighing 10.30 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Intake Plenum. The part 89017809 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.