Make sure this part fits

GM 12567648
Crankshaft Position Sensor

1994-2005 GM

Customer Questions & Expert Answers (16)
GM 12567648 Crankshaft Position Sensor
GM 12567648 Crankshaft Position Sensor
  • Part Description
    Sensor, Distributor (Also Knock Sensor); Engine Crankshaft Position Sensor
  • Replaces
    24508212, 10231684, 12550965
  • Manufacturer
    General Motors
Make sure this part fits
$95.30 MSRP: $193.55
You Save: $98.25 (51%)
Ships in 1-2 Business Days
1
ADD TO CART
  • Vehicle Fitment

    Year Make Model Trim Engine
    1996-1998 Buick CenturyCustom, Limited, Special6 Cyl 3.1 L GAS
    2002-2005 Buick RendezvousCX, CX Plus, CXL, CXL Plus6 Cyl 3.4 L GAS
    1994-1996 Buick SkylarkCustom, Gran Sport, Limited, Olympic Gold Edition6 Cyl 3.1 L GAS
    1994-1996 Chevrolet BerettaBase, Z266 Cyl 3.1 L GAS
    1994-1996 Chevrolet CorsicaBase6 Cyl 3.1 L GAS
    1995-1996 Chevrolet LuminaBase, LS6 Cyl 3.1 L GAS
    1996 Chevrolet Lumina APVBase, LS6 Cyl 3.4 L GAS
    1997-2003 Chevrolet MalibuBase, LS6 Cyl 3.1 L GAS
    1995-1996 Chevrolet Monte CarloLS6 Cyl 3.1 L GAS
    1997-2005 Chevrolet VentureBase, LS, LT, Plus, Value, Warner Bros.6 Cyl 3.4 L GAS
    View More
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 12567648 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 12567648 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the Crankshaft Position Sensor (24X) on Chevrolet Malibu? Posted by Customer
    A:
    Remove the 24x crankshaft position (CKP) sensor. To do that, first turn off the ignition, and then remove the serpentine Drive Belt from the Crankshaft Pulley. Put the car up on a hoist and take off the crankshaft Harmonic Balancer. Take note of the routing of the sensor harness before unwinding, then pull off the harness retaining clip then pull off the bolt then pull off the sensor electrical connector, then remove the bolts to clear the sensor. For installation, install the 24x Crankshaft Position Sensor and fasten it using bolts with the harness routed as specified during removal. Mount the harness retaining clip with the bolt and tighten the bolts to 10 n.m (8 lb ft). Then connect to the sensor electrical connector, install the balancer back at the crankshaft, lower the vehicle and fit in the serpentine drive. Lastly, complete the ckp system variation learn procedure.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the Crankshaft Position Sensor (24X) on Chevrolet Venture? Posted by Customer
    A:
    To replace the crankshaft position (CKP) sensor (24X), turn off the ignition, and remove the serpentine Drive Belt from the Crankshaft Pulley. Remove the right front tire and wheel assembly then the right front engine splash shield while the vehicle is up on a hoist. Next, take out the crankshaft Harmonic Balancer but be sure to note the routing of the sensor harness before removing it. Pull the harness retaining clip out with bolt, pull the sensor electrical connector off, and pull the sensor bolts out to remove the sensor. For the installation, install 24x Crankshaft Position Sensor using the bolts and run the harness as already pointed out above. Drive in the harness retaining clip with bolt and insert the bolts and tighten to 10 n.m (8 lb ft). Connect the sensor electrical connection, reinstall the balancer on the crankshaft, lower the vehicle, and finally, reinstall the serpentine Drive Belt.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the first step to replace the Crankshaft Position (CKP) Sensor for the 2002 Buick Rendezvous? Posted by Customer
    A:
    Turn OFF the ignition and raise the vehicle on a hoist.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Crankshaft Position Sensor
    Q:
    What should be done after securing the harness for the 2003 Buick Rendezvous? Posted by Customer
    A:
    Connect the sensor electrical connector, reinstall the balancer on the crankshaft, lower the vehicle, and perform the CKP System Variation Learn Procedure.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Crankshaft Position Sensor
    Q:
    How do you install the new 24X crankshaft position sensor for the 2005 Buick Rendezvous? Posted by Customer
    A:
    Place the sensor with bolts and route the harness as noted during removal.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Crankshaft Position Sensor
    Q:
    What should be removed after raising for the 2002 Chevrolet Malibu? Posted by Customer
    A:
    Remove the crankshaft harmonic balancer and note the routing of the sensor harness before removal.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Crankshaft Position Sensor
    Q:
    What is the final step after installing the sensor for the 2001 Chevrolet Malibu? Posted by Customer
    A:
    Connect the sensor electrical connector, reinstall the balancer on the crankshaft, lower the vehicle, and perform the CKP System Variation Learn Procedure.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Crankshaft Position Sensor
    Q:
    What is the torque specification for the sensor attaching bolt for the 2000 Chevrolet Malibu? Posted by Customer
    A:
    Tighten it to 8 N.m (71 lb in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Crankshaft Position Sensor
    Q:
    What should be done after raising the 2003 Chevrolet Malibu? Posted by Customer
    A:
    Remove the crankshaft harmonic balancer, noting the routing of the sensor harness before removal.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Crankshaft Position Sensor
    Q:
    How do you install the CKP sensor for the 2004 Chevrolet Venture? Posted by Customer
    A:
    Install the CKP sensor to the block, ensuring to follow the Fastener Notice in Service Precautions, and then install the sensor attaching bolt, tightening it to 11 N.m (97 lb in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Crankshaft Position Sensor
    Q:
    How do you disconnect the CKP sensor for the 2005 Chevrolet Venture? Posted by Customer
    A:
    Remove the harness retaining clip with the bolt and disconnect the CKP sensor electrical connector.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Crankshaft Position Sensor
    Q:
    What is the first step in the installation process for the 2001 Chevrolet Venture? Posted by Customer
    A:
    Place the 24X crankshaft position sensor with bolts and route the harness as noted during removal.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Crankshaft Position Sensor
    Q:
    How do you install the new CKP sensor for the 2002 Chevrolet Venture? Posted by Customer
    A:
    Place the 24X CKP sensor with the bolts, ensuring the harness is routed as noted during removal.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Crankshaft Position Sensor
    Q:
    What should be noted if DTCs other than P1336 are present for the 2003 Chevrolet Venture? Posted by Customer
    A:
    Consult the DTC List for further details.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Crankshaft Position Sensor
    Q:
    What is the torque specification for the sensor attaching bolt for the 2000 Chevrolet Venture? Posted by Customer
    A:
    Tighten it to 8 N.m (71 lb in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Crankshaft Position Sensor
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Crankshaft Position Sensor 12567648 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 12567648 Crankshaft Position Sensor is available in the market under the name GM Crankshaft Position Sensor. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 12567648 Crankshaft Position Sensor fits certain Chevrolet Malibu, Beretta, Corsica models, as well as Buick Skylark, Century, Rendezvous. Additionally, it is compatible with Pontiac Grand Am, Aztek, Montana and Oldsmobile Cutlass, Achieva, Alero models.
The original GM component designated by manufacturer part number 12567648 maintains top performance when functioning as the Sensor, Distributor (Also Knock Sensor); Engine Crankshaft Position Sensor unit. The component 12567648 is constructed from durable material and its dimensions span 6.4 x 3.2 x 3.1 inches while weighing 0.50 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Crankshaft Sensor. The part 12567648 has available replacement options 24508212, 10231684, 12550965. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.