Make sure this part fits

GM 12625987
Camshaft

2004-2011 GM

Customer Questions & Expert Answers (22)
GM 12625987 Camshaft
  • Part Description
    Camshaft, Engine
  • Replaces
    12566670, 12597293
  • Manufacturer
    General Motors
Make sure this part fits
$85.65 MSRP: $134.14
You Save: $48.49 (37%)
Currently Unavailable

Due to manufacturer supply shortage, this item isn't currently available for ordering.

  • Vehicle Fitment

    Year Make Model Trim Engine
    2005-2008 Buick LaCrosseCXS6 Cyl 3.6 L GAS
    2004-2006 Buick RendezvousCX, CXL, CXL Plus, Ultra6 Cyl 3.6 L GAS
    2004-2009 Cadillac CTSBase6 Cyl 3.6 L GAS
    2004-2006 Cadillac SRXBase6 Cyl 3.6 L GAS
    2005-2007 Cadillac STSBase6 Cyl 3.6 L GAS
    2008-2009 Chevrolet EquinoxSport6 Cyl 3.6 L GAS
    2008-2011 Chevrolet MalibuLT, LTZ6 Cyl 3.6 L GAS
    2007-2009 Pontiac G6GTP, GXP6 Cyl 3.6 L GAS
    2008-2009 Pontiac G8Base6 Cyl 3.6 L GAS
    2008-2009 Pontiac TorrentGXP6 Cyl 3.6 L GAS
    View More
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 12625987 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 12625987 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the final step in the replacement process for the 2006 Buick LaCrosse? Posted by Customer
    A:
    Reinstall the intake camshaft position actuator solenoid, camshaft sensors, camshaft cover, and finally, the upper intake manifold with the lower intake manifold.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What tool should be engaged to retain the timing chain for the 2005 Buick LaCrosse? Posted by Customer
    A:
    Engage the Timing Chain Retention Tool (EN46108) fully into the timing chain.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What tool should be used to prevent camshaft/engine rotation for the 2007 Buick LaCrosse? Posted by Customer
    A:
    Use an open-end wrench at the camshaft hex.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What should be done after installing the camshafts for the 2008 Buick LaCrosse? Posted by Customer
    A:
    Remove the EN-48313, using an open-end wrench to prevent rotation, then install and tighten the camshaft position actuators.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What should be marked for proper assembly for the 2007 Buick LaCrosse? Posted by Customer
    A:
    The camshaft timing chain and camshaft position actuators.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What components need to be removed after the intake manifolds for the 2006 Buick LaCrosse? Posted by Customer
    A:
    Remove the left bank camshaft cover, camshaft sensors, camshaft position actuator solenoid, and crankshaft balancer.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What should be applied to the forward edge of the front bearing caps for the 2004 Cadillac CTS? Posted by Customer
    A:
    Apply GM P/N 1052942 (Canadian P/N 10953466) or equivalent to ensure a proper seal.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What is the next step after marking for the 2009 Cadillac CTS? Posted by Customer
    A:
    Remove the camshaft position actuator bolt and the camshafts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What should be done after installing the camshaft seal for the 2004 Cadillac CTS? Posted by Customer
    A:
    Install the left camshaft drive sprockets and the left camshaft cover.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What tool is used to prevent camshaft/engine rotation for the 2005 Cadillac CTS? Posted by Customer
    A:
    Use an open-end wrench at the camshaft hex.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    How should the camshafts be installed for the 2006 Cadillac SRX? Posted by Customer
    A:
    Locate the camshafts to the cylinder head and assemble the camshaft actuators, ensuring the marks on the camshaft position actuator and the timing chain are aligned without tightening the camshaft position actuator bolt.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What is the next step after securing the EN-48313 for the 2008 Cadillac CTS? Posted by Customer
    A:
    Rotate the camshafts towards each other to create slack in the chain.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What should be done after aligning the marks for the 2004 Cadillac SRX? Posted by Customer
    A:
    Locate the camshafts to the cylinder head and assemble the camshaft actuators.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What is the torque specification for the camshaft intermediate drive shaft retaining bolts for the 2006 Cadillac STS? Posted by Customer
    A:
    Tighten them to 10 Nm (89 inch lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What is the first step to replace the right camshaft for the 2005 Cadillac SRX? Posted by Customer
    A:
    Begin by removing the upper intake manifold along with the lower intake manifold.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What components should be removed along with the camshaft for the 2007 Cadillac STS? Posted by Customer
    A:
    Remove the camshaft position actuator bolt and the camshaft bearing caps.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    When is it necessary to set the camshaft timing for the 2006 Cadillac STS? Posted by Customer
    A:
    It is necessary whenever the camshaft drive system has been disturbed, resulting in a loss of alignment between any chain and sprocket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What is the first step to replace the camshaft intermediate drive shaft for the 2005 Cadillac STS? Posted by Customer
    A:
    First, remove the camshaft intermediate drive shaft sprocket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What components need to be taken off after removing the intake manifolds for the 2005 Buick LaCrosse? Posted by Customer
    A:
    The left bank camshaft cover, camshaft sensors, and camshaft position actuator solenoid.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What is the final step in the process for the 2008 Chevrolet Malibu? Posted by Customer
    A:
    Finally, install the intake camshaft position actuator.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    Q:
    What should be done with the used roller followers for the 2008 Chevrolet Malibu? Posted by Customer
    A:
    Ensure that used roller followers are returned to their original positions on the camshaft; if replacing the camshaft, replace the actuated roller followers as well.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Camshaft
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Camshaft 12625987 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 12625987 Camshaft is available in the market under the name GM Camshaft. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 12625987 Camshaft fits certain Chevrolet Malibu, Equinox models, as well as Cadillac CTS, SRX, STS. Additionally, it is compatible with Buick LaCrosse, Rendezvous and Pontiac G8, G6, Torrent models.
The original GM component designated by manufacturer part number 12625987 maintains top performance when functioning as the Camshaft, Engine unit. The component 12625987 is constructed from durable material and its dimensions span 21.8 x 3.2 x 3.0 inches while weighing 4.20 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 12625987 has available replacement options 12566670, 12597293. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.