GM 19417578
Stabilizer Link, Front

The first step to replace the sway bar link within the front suspension demands the proper lifting and supporting of the vehicle. Begin by removing the tire alongside wheel assembly and proceed with disassembly of the sway bar link bolt and nut before extracting the sway bar link from the vehicle. The first step for installation involves putting the sway bar link into position while following the Fastener Notice that appears in Service Precautions. The sway bar link bolt should be installed followed by the addition of a nut that needs to be tightened to 23 N.m (17 lb ft). The tire and wheel assembly installation concludes by placing both elements back then lowering the car down.

A vehicle stability shaft link replacement in front suspensions requires first lifting and stabilizing the vehicle. Start by removing the sway bar link bolt and nut before the pry bar insertion to take out sway bar link insulators and spacer. The installation steps involve using the pry bar to position sway bar link insulators and spacer before installing the sway bar link along with its insulators. You should apply torque of 18 Nm (13 ft. lbs.) to the sway bar link nut before you put on the sway bar link bolt and nut. Finally, lower the vehicle.

The service process for sway bar link starts by elevating and supporting the vehicle properly. Tires with their wheels need extraction before beginning any service operations. First dampen the sway bar link with the bolt and nut before extracting it from the vehicle. Put the sway bar link inside the vehicle while following the Fastener Notice in Service Precautions. Fasten the sway bar link with its bolt and nut as you tighten the nut to 23 Nm (17 ft. lbs.). The procedure concludes with replacing the tire and wheel assembly after lowering the vehicle.

Service of the sway bar link requires two steps. First, secure the vehicle through proper elevation then secure it. The first step requires removal of the tire together with its wheel assembly. The vehicle operator must first support the vehicle correctly then proceed with removing the sway bar link bolt and nut before pulling out the sway bar link from the vehicle. Place the sway bar link within the vehicle following all guidance in the Fastener Notice. Fasten the sway bar link bolt along with the nut while torquing the nut to a 23 Nm (17 ft. lbs.) setting. Lower the vehicle while putting back on the tire and wheel assembly.

The first step to service the front sway bar link is to correctly support and elevate the vehicle. The tire and wheel assembly should be removed first before the sway bar link bolt and nut are undone to extract the sway bar link from the vehicle. When installing the sway bar link into the vehicle maintain strict adherence to the Fastener Notice described in Service Precautions. Fasten the sway bar link bolt to the nut then tighten it to 23 Nm (17 ft. lbs.). Complete the process by first reinstalling the tire with its wheel assembly then lowering the vehicle.

The process to replace sway bar links in front suspensions starts by supporting the vehicle at an appropriate height. After lifting the vehicle properly you must take off the wheel and tire unit and disconnect the sway bar link bolt and nut before extracting the sway bar link from the vehicle. The installation process requires putting the sway bar link into the vehicle while closely following the instructions of Fastener Notice in Service Precautions. Fasten the sway bar link pieces with the bolt followed by the nut until the torque reaches 23 Nm (17 ft. lbs.). Complete the process by first reinstalling the tire along with wheel assembly then lowering the vehicle.

The first step to replace the front sway bar link involves properly raising and supporting the vehicle. The deputy will start by removing the tire then the wheel followed by the sway bar link bolt and nut. Removal of the sway bar link should be performed from the vehicle. Place the sway bar link into the vehicle through its proper position but stay compliant with the delivery condition statements mentioned in the service precautions. To complete the installation position the sway bar link bolt together with the nut so that you tighten the nut to 23 Nm (17 ft. lbs.). Reinstallation of the tire begins by putting the wheel back before returning the vehicle to its original lowered position.

Remove the stabilizer shaft link nut from the stabilizer shaft link and the stabilizer shaft.

Reinstall the tire and wheel assembly and lower the vehicle.

Install the stabilizer shaft link to the vehicle and connect it to the stabilizer shaft.

A wrench is needed to hold the stabilizer shaft link.

The tire and wheel assembly.

The tire and wheel assembly.

Take out the stabilizer shaft link from the vehicle.

Lower the vehicle.

Lower the vehicle.

35 Nm (26 ft. lbs.).

Take out the stabilizer shaft link from the vehicle.

Use a wrench to hold the stabilizer shaft link while removing the nuts.

First, raise and support the vehicle.

Install the new stabilizer shaft link, ensuring to follow the Fastener Notice in Service Precautions.

Use a pry bar.

Install the stabilizer shaft link bolt and nut.

Position the new stabilizer shaft link and ensure to follow the fastener notice in service precautions.

Connect the stabilizer shaft link to the strut.

Install the stabilizer shaft link nut to the stabilizer shaft link and the stabilizer shaft, tightening it to 35 N.m (26 lb ft).

Lower the vehicle.

Raise and support the vehicle.

Raise and support the vehicle appropriately.

Raise and support the vehicle appropriately.

Secure it with the bolt and nut, tightening the nut to 23 N.m (17 lb ft).

Reinstall the tire and wheel assembly and lower the vehicle.

Reinstall the tire and wheel assembly and lower the vehicle.

Tighten the stabilizer shaft link to strut nut to 35 Nm (26 ft. lbs.).

Tighten the stabilizer shaft link to strut nut to 35 Nm (26 ft. lbs.).

The tire and wheel assembly.

Take out the stabilizer shaft link from the vehicle.

Position the stabilizer link into the vehicle, adhering to the Fastener Notice in Service Precautions.

Install the upper stabilizer shaft link nut to the stabilizer shaft link and the strut, tightening it to 52 Nm (38 lb ft).

Tighten it to 52 Nm (38 ft. lbs.).

Raise and support the vehicle.

Install the stabilizer shaft link nut to the stabilizer shaft link and the strut, tightening it to 52 Nm (38 ft. lbs.).

Install the upper stabilizer shaft link nut to the stabilizer shaft link and the strut.

Place the stabilizer link into the vehicle, ensuring to adhere to the Fastener Notice in Service Precautions.

Raise and support the vehicle appropriately.

Raise and support the vehicle.

Install the new stabilizer shaft link, ensuring to follow the Fastener Notice in Service Precautions.

Position the stabilizer link into the vehicle and install the stabilizer shaft link bolt and nut.

Raise and support the vehicle.

The tire and wheel assembly.