Make sure this part fits

GM 10360742
Mount Bracket, Passenger Side

2004-2011 GM

Customer Questions & Expert Answers (32)
GM 10360742 Mount Bracket, Passenger Side
  • Part Description
    Bracket, Engine Mounting; Engine Mount Bracket; Motor Mount
  • Position
    Passenger Side
  • Replaces
    25756320
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2004-2009 Cadillac SRXBase6 Cyl 3.6 L GAS
    2006-2011 Cadillac STSBase, Platinum6 Cyl 3.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 10360742 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 10360742 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be installed under the oil pan for support for the 2005 Cadillac SRX? Posted by Customer
    A:
    A screw jack with a block of wood.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What do you do after removing the engine mount retaining nut for the 2007 Cadillac SRX? Posted by Customer
    A:
    Take out the engine mount from the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the first step to replace the left engine mount bracket for the 2004 Cadillac SRX? Posted by Customer
    A:
    Raise and support the vehicle, then install a screw jack with a block of wood under the oil pan for support.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What should be done after tightening the bolts for the 2005 Cadillac SRX? Posted by Customer
    A:
    Remove the transmission support, reinstall the exhaust system, and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should the retaining bolts be tightened to during installation for the 2008 Cadillac SRX? Posted by Customer
    A:
    60 N.m (44 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What conditions should be observed that necessitate replacement of the transmission mount for the 2004 Cadillac SRX? Posted by Customer
    A:
    The hard rubber surface shows heat check cracks, the rubber is separated from the metal plate, or the rubber is split through the center.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the next step after raising the 2004 Cadillac SRX? Posted by Customer
    A:
    Remove the lower engine mount retaining nut.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the next step after removing the upper retaining nut for the 2006 Cadillac STS? Posted by Customer
    A:
    Take out the right engine mount bracket mounting bolts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What should be done after positioning the engine mount for the 2007 Cadillac STS? Posted by Customer
    A:
    Install the engine mount retaining nut and tighten it to 80 N.m (59 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    How should the engine mount be positioned during installation for the 2006 Cadillac SRX? Posted by Customer
    A:
    Position the engine mount onto the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the first step in the installation process for the 2006 Cadillac STS? Posted by Customer
    A:
    Position the new transmission mount onto the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be done after tightening the transmission mount bolts for the 2009 Cadillac SRX? Posted by Customer
    A:
    Install the body mounting bolts and tighten them to 60 Nm (44 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the first step to replace the transmission rear mount on a 5L40-E/5L50-E automatic transmission for the 2009 Cadillac SRX? Posted by Customer
    A:
    Raise and support the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What bolts need to be removed to take out the transmission mount support assembly for the 2008 Cadillac SRX? Posted by Customer
    A:
    The transmission mount support to body mounting bolts and the transmission mount support to transfer case mounting bolts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be done at the end of the process for the 2005 Cadillac SRX? Posted by Customer
    A:
    Remove the screw jack and block of wood from under the oil pan and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What needs to be detached from the mount assembly for the 2007 Cadillac SRX? Posted by Customer
    A:
    Detach the transmission vent hose from the six retainers on the mount assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be removed after discharging the A/C system for the 2008 Cadillac STS? Posted by Customer
    A:
    Remove the tower brace and raise the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the first step in the installation process for the 2007 Cadillac SRX? Posted by Customer
    A:
    Position the engine mount bracket back onto the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What is the final step after securing the engine mount for the 2008 Cadillac SRX? Posted by Customer
    A:
    Lower the engine using the screw jack until the weight is resting on the mount, then install the engine mount retaining nut, tightening it to 80 N.m (59 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What should be removed after raising the engine for the 2009 Cadillac SRX? Posted by Customer
    A:
    Remove the upper engine mount retaining nut and the engine mount itself, taking care not to distort or bend the engine mount heat shield.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What should be removed after the upper retaining nut for the 2007 Cadillac STS? Posted by Customer
    A:
    Remove the right engine mount bracket mounting bolts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What bolts need to be removed to take out the transmission mount support assembly for the 2010 Cadillac STS? Posted by Customer
    A:
    The transmission mount support to body mounting bolts and the transmission mount support to transfer case mounting bolts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the first step to replace the right engine mount for the 2004 Cadillac SRX? Posted by Customer
    A:
    Raise and support the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the first step to replace the transmission mount for the 2008 Cadillac STS? Posted by Customer
    A:
    Raise and support the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the first step to replace the left side engine mount bracket for the 2008 Cadillac STS? Posted by Customer
    A:
    First, install the engine support fixture.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What needs to be detached from the mount assembly for the 2007 Cadillac STS? Posted by Customer
    A:
    Detach the transmission vent hose from the six retainers on the mount assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the final step after installing the engine mount for the 2006 Cadillac STS? Posted by Customer
    A:
    Reinstall the left engine mount bracket and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    How should the engine be supported during the replacement for the 2009 Cadillac SRX? Posted by Customer
    A:
    Install a screw jack with a block of wood under the oil pan for support.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the torque specification for the M 10 engine mount bracket mounting bolts for the 2006 Cadillac SRX? Posted by Customer
    A:
    Tighten them to 60 Nm (44 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What is the first step to replace the left side engine mount for the 2008 Cadillac SRX? Posted by Customer
    A:
    Raise and support the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the first step to replace the right side engine mount for the 2008 Cadillac STS? Posted by Customer
    A:
    Raise and support the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Mount Bracket, Passenger Side 10360742 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 10360742 Mount Bracket, Passenger Side is available in the market under the name GM Engine Mount, Motor And Transmission Mount, Engine Mount Bracket. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 10360742 Mount Bracket, Passenger Side fits certain Cadillac SRX, STS models.
The original GM component designated by manufacturer part number 10360742 maintains top performance when functioning as the Bracket, Engine Mounting; Engine Mount Bracket; Motor Mount unit at its Passenger Side. The component 10360742 is constructed from durable material and its dimensions span 10.1 x 8.0 x 4.9 inches while weighing 1.90 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 10360742 has available replacement options 25756320. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.