GM 19257054
Bulb & Socket

A driver should first turn off the lamp switch then wait for the bulb to cool down before changing the bulb to avoid shard glass injuries. You should handle the bulb by the base only while wearing protective eye gear and keeping the bulb glass untouched plus moisture-free from dirt. Disposal of used bulbs should be proper while all halogen bulbs must remain beyond children's grasp. The replacement procedure for the passenger side high beam headlamp bulb includes separate steps while all remaining headlamps need their bulb (3 or 4) twisted counterclockwise to release retainer tabs before pulling out the bulb to disconnect it from the wire harness. The installer should never contact the bulb or allow moisture exposure because exposing it to these conditions leads to bulb detonation after switch activation. Burn the bulb using alcohol or the appropriate degreaser to prevent explosion following skin oil or moisture contact. Connect the wire harness to the new headlamp bulb and push the bulb (3 or 4) into the headlamp assembly before rotating it clockwise for retainer tab locking. Reinstall the headlamp assembly if required.

Bulb replacement requires stopping the lamp switch and allowing the bulb to cool in order to avoid glass shattering incidents. Wear protective eye gear when handling bulbs since you should grip only the base to prevent touching the glass surface while maintaining bulb cleanliness in a dry condition. After using the bulb dispose it properly and keep halogen bulbs from reaching children's hands. Start by removing the headlamp followed by removing the inoperative headlamp bulb designated as 3 or 4 from the headlamp assembly before disconnecting it from the wire harness. Before hooking the wire harness to the headlamp bulb users should avoid touching the bulb surface or permitting it to reach moist or oily substances because this contact can trigger bulb explosion when the light is powered on. In case of contact wash the bulb with alcohol followed by a suitable degreasing substance before drying it with a wiping motion. Based installation of the headlamp bulb (3 or 4) into the headlamp assembly then reattach the assembly.

In order to change the front fog lamp bulb, one has to first raise the vehicle and support accordingly. Detach the electrical connector from the front fog lamp bulb being cautious of the halogen bulb caution. Turn the front fog lamp bulb base counterclockwise to release it and then carefully remove the front fog lamp bulb from the front fog lamp assembly. For installation, insert the new fog lamp bulb into the front fog lamp assembly carefully and turn bulb base clockwise to lock. Lastly, reattach the electrical connector to the front fog lamp bulb & bring down the vehicle.

The first step to replace the front fog lamp bulb requires removal of the front bumper fascia deflector. Turn off the electrical connector from the front fog lamp bulb/socket before rotating its front fog lamp bulb/socket counterclockwise to disengage it. There is a halogen bulb caution you should follow as you carefully take out the fog lamp bulb/socket from the front fog lamp assembly. To replace the fog lamp install the bulb/socket by rotating it clockwise until it reaches full seating. Then reconnect the electrical connector to the front lamp socket by observing the halogen bulb caution. You should reattach the front bumper fascia deflector in its proper position.

After opening the hood users should use light pressure on the headlamp lens to secure place before removing the retainers. You can release the headlamp retainers by lifting them up and then step by step extract the mounting tabs from their location points on the upper fascia support combined with fender reinforcement. Unplug the Headlight electrical connector before extracting the Headlight unit from its place. You must first remove the rubber access covers installed behind the headlamp bulb/sockets with replacement functions in mind while observing the important halogen bulb caution. The counterclockwise rotation on the headlamp bulb/socket unlocks it before you pull the unit from the headlamp while disconnecting its electrical connector. To install the new headlamp bulb/socket connect the electrical connector first before putting the bulb/socket in the headlamp while rotating it clockwise until full seating occurs. Place the rubber access covers back then attach the electrical connector to the headlamp component. Use gentle pressure that pushes the lens of the headlamp as you insert the mounting tabs into the slots found between the upper fascia support and fender reinforcement. Press the retainers over the mounting tabs before securing them completely. Examine the headlamp for its proper seating position then verify the headlamp aim if new headlamps were installed and following maintenance operations disturbed any mounting brackets. Finally, close the hood.

Start the process of front fog lamp bulb replacement by removing the front bumper fascia deflector. First disconnect the electrical connector of the front fog lamp bulb/socket while following the halogen bulb caution guidelines. Completely rotate the front fog lamp bulb/socket to the counterclockwise direction until it releases itself before removing the bulb/socket from the front fog lamp assembly. The process of installation requires inserting the fog lamp bulb/socket into its opening while turning it clockwise until it is securely seated while observing all halogen bulb caution indicators. Reinstall the front bumper fascia deflector after you connect the electrical connector between the front fog lamp bulb/socket.

Beginning the replacement of your rendezvous headlamp bulb requires you to start by opening the hood then removing the thumb screw found at the rear side of the lamp. The ball stud detaches from the grommet after pulling the headlamp straight forward when you free the retainer clip from its position. This enables you to remove the headlamp from the upper fascia support. Rephrase the following sentence. Begin by disconnecting the electrical connector and turning the bulb(s) counterclockwise to remove them. The trim tabs connecting the headlamp must be unlocked while pulling off the trim so 3m™ adhesive remover p/n 8984 or equivalent can be used to remove the adhesive. To install the headlamp trim use new adhesive tape 3m™ p/n 6382 or an equivalent material which you must position on the headlamp and securely press until the end tabs fully fit. To install the bulbs follow a clockwise rotation pattern while connecting the electrical cable to its proper place in the upper fascia support panel. First put the headlamp upper fascia support ball stud in the ball seat before tightening the thumb screw while guiding the vertical retainer downward to secure in place. The last step includes checking the headlamp aim if a new headlamp was installed or if service and repairs took place in the front end area and closing the hood.

Begin headlamp bulb or cornering, sidemarker, park, or turn signal bulb replacement by opening the hood before applying light pressure to keep the headlamp lens in place while removing the retainers. The first step involves raising the retainers on each headlamp until they detach before taking out the retainers. First loosen the retaining tabs on all headlamp mounting slots on both the upper fascia support and fender reinforcement before detaching the electrical connector from the headlamp and finally removing it. Check all bulbs/sockets for replacement while observing the essential Halogen Bulb Caution then take out the rubber access covers located behind the headlamp bulb/sockets. Turn the headlamp bulb SOCKET counterclockwise to open it before you disconnect the electrical CONNECTOR from the bulb SOCKET. To install the new headlamp bulb/socket connect its electrical connector first before moving it into position and rotating it clockwise to reach complete seating. After installation of the rubber covers return to the headlamp and complete the electrical connector connection. Install the headlamp mounting tabs by placing them in the slots of the upper fascia support and fender reinforcement while applying light pressure on the lens through the installation of retainers. Press the retainers onto the mounting tabs until they attach completely to their positions. The last step includes inspecting the headlamp for proper seating as well as checking its aim when the vehicle features new headlamps or when service could have affected mounting brackets. Close the hood afterward.

The first step to replace a headlamp bulb includes taking out the lamp assembly. Perform this task by pressing the top lever tab until the headlamp bulb cover can be rotated downwards while following the halogen bulb caution guidelines. Placing the socket and bulb in a secure spot on the headlamp requires a two-step process. Disconnect the bulb from the socket before moving on to remove socket and bulb from headlamp. Begin the installation process by fixing the bulb inside the socket then reconnect the socket with bulb to the headlamp. Replace the headlamp assembly after you complete the steps to secure the headlamp cover with correct engagement of the lever tab.

The first step to exchange the rear fog lamp bulb requires removal of the rear fog lamp lens by unscrewing its retaining screws. Pull the bulb out from the rear fog lamp assembly by turning it counterclockwise before tucking the bulb clockwise into place. Proceed with careful handling of the halogen bulbs throughout this operation. Installation requires users to place the new bulb into the fog lamp assembly before rotating it clockwise for tight fixing. Reconnect the rear fog lamp lens after you install its retaining screws which you must tighten to 2 n.m (18 lb in). Regular inspection of the rear fog lamp will determine its correct functional state.

The first step to change fog lamp bulbs requires turning off the lamp switch and waiting for the bulb to cool down as a safety precaution against broken glass pieces. Handle the bulb by its base for safety while wearing protective eye gear to keep the glass part away from contact and moisture-free from dust. The bulb needs proper disposal methods while children should have no access to halogen bulbs. First disconnect the electrical connector located at the back end of the fog lamp bulb. The fog lamp bulb needs removal by rotating it counter-clockwise until it reaches a 45-degree position before throwing away the non-functional lamp. To mount the fog lamp bulb into the housing position it properly then rotate it 45 degrees clockwise for installation. The installation completes with connecting the electrical connector.

Starting the bulb servicing process requires removing both the front grille and headlamp retainer pins until the headlamp assembly pulls out to gain access to the electrical connector so you can disconnect it. The rubber cup needs removal to reach the headlamp bulbs before the bulbs can be extracted. Installation requires you to switch the high beam bulb with another high beam bulb featuring a red gasket as well as the low beam bulb with another low beam bulb having a gray-tipped yellow-based gasket. Complete the installation by attaching new bulbs first before putting the rubber cup and reattaching the electrical connector to the lamp assembly. Put the reinstalled lamp component back into the vehicle while maintaining it through the headlamp assembly retainer pins. Finish by reinstalling the front grille.

Starting the 9005 High Beam headlamp bulb replacement process requires a turned-off lamp switch and cool bulbs. Protection for your eyes must always be worn while handling bulbs by their base section and never touch the glass surface or let moisture reach or touch the bulb. Discard the used bulb correctly and store halogen bulbs where children cannot access them. Start by removing the upper filler panel before turning the inner headlamp bulb counter-clockwise 45 degrees to remove it from behind the headlamp panel housing. Remove the inoperative bulb by first disconnecting the electrical connector that belongs to the bulb. Connect the electrical connector to the new headlamp bulb before positioning the bulb into the headlamp capsule. Then twist it clockwise an angle of 45 degrees for installation. Reattach the upper filler panel as a last step. Keep the new bulb free of both contact and moisture contact since both oil and moisture can lead the bulb to explode upon use. Use alcohol or an appropriate degreasing agent to clean the bulb before drying it.

Replacing either the headlamp assembly or headlamp bulb (HID) requires you to extract the front grille followed by removing headlamp retainer pins and then drawing out the headlamp assembly in order to disconnect the electrical connector. Access to the headlamp bulbs becomes possible by first removing the rubber cups. Begin by installing the new bulbs before putting on the rubber cups for installation. The electrical connector ties to the lamp assembly first while replacing the lamp assembly back to its position in the vehicle by using headlamp assembly retainer pins before securing the front grille. Be vigilant about the high voltage and current operations of the high intensity discharge system since opening the ballast or arc tube assembly or probing between electrical connectors causes severe shocks and burns. Maintain safe distances between the arc tube and the headlamp housing as well as bulb shield when uninstalling or installing to prevent any damage from occurring.

Car users must start by removing the headlamp assembly before they can change the bulb. Turn the headlamp bulb counterclockwise to unfasten it from the headlamp assembly after disconnecting its electrical connector. You can install the new headlamp bulb by placing it into the headlamp assembly before securing it by turning it clockwise. The installation process begins with connecting the electrical connector to the headlamp bulb while the headlamp assembly should be reinstalled onto the vehicle. Consult the vehicle/application id page to view the description of rpo codes presented in this article and its images.

The replacement process of headlamp bulbs starts with the hood opening for removal of the park/turn signal lamp assembly. Start by removing both headlamp pins to detach the assembly from its position to reach the electrical connector which must be disconnected. According to procedure remove the bulb from its position in the headlamp assembly by rotating it in a counterclockwise direction. The new bulb should be inserted into the headlamp assembly by turning it clockwise until it locks into position. The replacement should be between a red-gasket high beam bulb and another high beam bulb and between a low beam bulb with gray tip and yellow gasket base and an additional low beam bulb. Secure the headlamp assembly by attaching the electrical connector to the bulb and then reinstate the headlamp along with inserting the retainer pins into their locks. Complete the installation by refitting the park/turn signal lamp assembly while conducting a test of its operational state.

You should start replacement of the rear fog lamp bulb by taking out the screws holding the lens and removing the lens itself. Begin by inserting a small amount of force into the bulb which you need to rotate 1/4 turn in the counterclockwise direction until it comes out from the socket. First deploy the new bulb into the socket and gently push it while making a quarter turn in the clockwise direction. Reposition the lamp lens to the assembly and secure it by attaching the screws that require a torque limit of 1.5 N.m (13 lb in).

In order to replace the headlamp bulb, one should ensure that the headlamp switch is off and let the bulb cool. Open the hood and unfasten the screw holding the corner capsule to the composite headlamp, followed by the three bolts securing the composite headlamp. Carefully remove the headlamp and untangle the electrical connectors before pulling the headlamp bulbs. To install start by inserting the new headlamp bulbs and reattach the electrical connectors. Refit the headlamp assembly, ensuring the composite headlamp bolts are tightened to 13 n.m (115 lb in) and refit the corner capsule, this is secured with a screw which is tightened to 5 n.m (44 lb in). Finally, close the hood ensuring you handle the halogen bulbs in a responsible way to prevent injury and dispose of the used bulb responsibly.

You must start by switching off the rear fog lamp then waiting until the bulb cools before handling it due to its compressed gas nature that creates injury risks from shattering during improper care of halogen bulbs. The bulb should always be handled by securing it to its base while wearing protective eyesight equipment and maintaining the glass areas clean from contaminants and water. Users must throw out the used bulb right away while keeping all halogen bulbs far from children. Start by taking off the lift gate applique followed by rotating the fog lamp bulb socket counterclockwise for detachment from the assembly to extract it. The fog lamp bulb needs removal from its socket. Begin the installation by putting the new fog lamp bulb into the socket before turning the fog lamp bulb socket clockwise back into position in the applique assembly while connecting its electrical connector before reinstalling the lift gate applique.

The first step to replace the fog lamp bulb is to detach its electrical connector. Proceed by turning the bulb counterclockwise before extracting it from the fog lamp assembly. You should proceed with care when handling halogen bulbs. The bulb installation process requires insertion into the fog lamp assembly while twisting clockwise until secure and connecting the electrical connector.

The process of fog lamp bulb replacement on the front of the vehicle begins with proper lifting and support of the vehicle. Users must open the access door present inside the front bumper air deflector when working with Camaro and Firebird models. Remove the push pin holders which sit beneath the center area at the front side of the Trans Am vehicle fascia. Disengage the electrical connector from the fog lamp followed by extracting the fog lamp bulb from its connector. The installation procedure of the new bulb requires users to attach it to the electrical connector followed by reattachment of the electrical connector to the fog lamp. Put back the push pin retainers which should be positioned at the bottom center of the front fascia in Trans Am models and close the access door in the front bumper air deflector in Camaro and Firebird models before you lower the vehicle.

In order to replace the headlamp assembly or headlamp bulb or cornering, sidemarker, park, and turn signal bulb, the procedure starts with opening the hood. Secure the headlamp and pull forward on the release tabs to remove the headlamp. Remove the electrical connectors from the lamp sockets taking notice of the halogen bulb caution. Unscrew the headlamp or park lamp sockets with a counter clockwise motion and remove the headlamp or park bulb from the socket. For installation, press the headlamp or park bulb into the socket and rotate the socket clockwise to install the headlamp or park lamp. Attach the electrical connectors to the lamp sockets and fit the headlamp by pushing it directly into the headlamp mounting panel. Position the headlamp and depress the release tabs and inspect and adjust the aim of the headlamp as required. Finally, close the hood.

You should start by raising the hood before you untwist the headlamp socket located at the back of the unit to finally remove the headlamp bulb from its harness. It is vital to disable the lamp switch and let the bulb reach room temperature before any installation process begins. Use your eyes and hands only touch the base section of the bulb because glass surfaces should stay clear from water and all other substances including dirt. Discard the old bulb correctly and place all halogen bulbs somewhere children cannot reach. When exposed to contact with touch or water a bulb should be dried while cleaning it with alcohol or appropriate degreasing liquid. Finish the procedure by inserting the new headlamp bulb into the harness socket before attaching the harness socket to the rear of the headlamp and lastly closing the hood.

Users must start bulb modification by opening the hood before unraveling the harness socket from the headlamp's rear section to extract the bulb from the socket. To work with the lightbulbs containing gas in a pressure environment handle them only by their base while completely turning off the lamp switch and taking time for the bulb to achieve complete coolness first. Eye protection must be worn at all times while operating and you should grip the bulb base only because contact with the glass should be avoided along with keeping dirt and moisture at bay from the bulb. Discard any used bulbs correctly while putting halogen bulbs where children cannot access them. Stay clear from letting moisture or oil near the bulb because contact may trigger bulb explosion during activation; when such contact happens, wash the bulb using alcohol or appropriate degreasers and dry it thoroughly. In the final step of installation you must insert the new bulb into the harness socket then apply the socket to the rear of the headlamp before closing the hood.

The process to change headlamp bulbs begins by turning off the headlamp switch and placing the ignition switch in the lock position. Locate the front grille then remove all bolts which secure the headlamp front unit. For bulb replacement of either the high beam headlamp or low beam headlamp you must first apply a 1/4 counter-clockwise turn while pushing carefully. Then disconnect the electrical connector. The installation of the new bulb requires first attaching the electrical connector before gently pushing in the high beam headlamp and low beam headlamp while rotating them 1/4 turn clockwise. Tighten the headlamp-retaining bolts to 10 n.m (89 lb in) before checking the headlamps work correctly and then reinstalling the front grille. Minimize handle of halogen bulbs by treating them gently and maintaining a distance from the glass portion while keeping them dry since moisture poses an explosion hazard. After usage dispose of the used bulb while keeping all halogen bulbs away from children's accessible areas.

First disconnect the electrical connector of the headlamp bulb while turning off the headlamp switch for bulb replacement. Take proper precautions when handling halogen bulbs because their content under pressure can result in bulb shattering when improperly managed. Safe bulb replacement requires turning the lamp switch off and waiting for the bulb to cool down first along with wearing protective eye gear when handling the bulb exclusively at its base and also keeping it free from water and dust before proper disposal of used bulbs and storing halogen bulbs away from children. The bulb requires counterclockwise rotation to detach from the headlamp before you should remove it. First insert the new bulb into the headlamp space then follow by twisting it clockwise to lock it into position. Reestablish the electrical connector by attaching it to the headlamp bulb.

The first step to replace the fog lamp bulb requires turning off the fog lamp switch and disconnecting the electrical connector. The bulb socket requires counterclockwise rotation to detach from the fog lamp housing before removal of the socket. Place the bulb socket out of the electrical connection point and slot the new bulb into the socket. Follow the slots in the fog lamp housing while inserting the bulb socket tabs and put the socket in place. The socket insertion process requires users to turn it clockwise until it reaches complete seating.

Service of the fog/driving lamp bulb begins with raising and supporting the vehicle. Start by taking out the front fascia lower close out panel followed by a removal process of brake caliper cooling duct from front fascia installation. Finally, set this duct aside. The service professional should disconnect the electrical connector from the fog lamp bulb/socket while being attentive to the Halogen Bulb Caution. Clockwise rotation of the fog lamp bulb/socket will release it from the fog lamp so you can remove it. First connect the electrical front fog lamp connector before you rotate the fog lamp bulb/socket clockwise into the fog lamp assembly. Reposition the brake caliper cooling duct to the front fascia then apply gentle pressure to secure it and conclude by fitting the front fascia lower close out panel. Check and adjust the aim of fog lamps when lowering the car.

Opening the hood is the first step for servicing a headlamp bulb while doing headlamp bulb replacement work. Turn the headlamp motor/actuator manual control knob counterclockwise manually to lift the headlamp up. The service begins with disconnecting the electrical connector between the headlamp wiring harness and forward lamp wiring harness while also removing the headlamp bezel. Attention to detail about halogen bulb safety must be maintained. You can reach the headlamp bulb by accessing the opening as the headlamp assembly meets the frame rail. Then remove the correct bulb from its capsule by turning it slowly. You should detach the electrical connector from the bulb using a flat-bladed screwdriver. Begin headlamp bulb installation by putting the bulb inside the capsule followed by plugging the electrical connector to it. To finish the procedure the technician must replace the headlamp bezel before operating the headlamp motor/actuator manual control knob for clockwise rotation until the lamp reaches the desired position. After this step they must reconnect the headlamp wiring harness to the forward lamp wiring harness electrical connector. According to the final step you should close the hood after which you should aim the headlamps manually with either the screen method or mechanical method.

You need to turn off the lamp switch prior to replacing the fog lamp bulb on the Luxury Y91 because hot bulbs can risk injury through shattered glass. Wear protective eye gear when replacing the bulb and grasp the base portion by this section because touching glass must be prevented and the bulb needs to stay clear of liquids or debris. Separate the electrical connector attached to the fog lamp bulb back and remove the bulb when turning it in a counterclockwise direction 45 degrees. Insert the new fog lamp bulb into its housing after which you can lock it into position through 45 degree clockwise rotation. The final step requires connecting the electrical connector. Discard the used bulb properly and place halogen bulbs where children cannot access them.

The solution to replace headlamp bulbs starts by turning off the headlamp switch while waiting for the bulb to reach normal temperature. Use protective eyewear when handling the bulb and maintain contact with its base only because touching the glass leads to harm. The bulb's cleanliness along with dry condition should be maintained while proper disposal methods must be followed for used equipment. First reach in from the engine compartment to twist the bulb counterclockwise and pull it out from the headlamp capsules. Start by unfastening the 2 long screws from the radiator support top then draw forward the headlamp assembly. The burnt-out bulb assembly should have its electrical connection disconnected. Substitution occurs by replacing high beam bulbs with red gasket versions and low beam bulbs with gray tip bulbs featuring yellow gaskets at their base. Insert the new bulb assembly into the headlamp assembly with clockwise rotation to face down the connector. First, plug the electrical connector into the bulb assembly followed by reinstallation of the headlamp assembly and fastening completion using the 2 long screws applied to the radiator support's top area for tight installation.

Maintenance procedures for the headlamp bulb begin by removing the relevant headlamp assembly from its bracket followed by disconnecting electrical connectors from the target bulb while paying attention to the halogen bulb caution. To begin the headlamp bulb service you must twist the bulb base in the opposite direction before pulling it out from the assembly. Insert the new headlamp bulb properly into its place within the assembly before tightening the bulb base clockwise to lock it in position. First reconnect all electrical connectors to the bulbs inside the headlamp before reattaching the assembly to the headlamp bracket.

The first step for bulb replacement begins with the removal of the rear fog lamp lens through retaining screw removal. People should exercise caution with the safe use of halogen bulbs. Rotate the bulb to the opposite direction while extracting it from the rear fog lamp assembly. Start the installation process by inserting the new bulb into the rear fog lamp assembly and rotating it by clockwise movements. Reinstall the rear fog lamp lens after securing it with the retaining screws by tightening them to 2 n.m (18 lb in). The inspection of the rear fog lamp operation completes the procedure.

The first step for rear fog lamp bulb replacement requires removal of lens retaining screws at the rear lamp position. Be vigilant in protecting yourself from halogen bulbs while handling them. Gently twist the bulb while rotating it counterwise until it comes out from the rear fog lamp housing. Transport the new bulb inside the rear fog lamp assembly before turning it clockwise to install. Screw the rear fog lamp lens retaining screws until they reach 2 n.m torques (18 pound-inch). Confirm the operation of the rear fog lamp after the last check.

You can change the Headlight Bulb after turning off the lamp switch while waiting for the bulb to cool down. Protect your eyes at all times while you must grip the bulb only at its base to prevent touching the glass. Always maintain the bulb in a clean dry state before following safe procedures for proper bulb disposal. Inspection of the headlamp retainer pins requires rotating them before extracting the pins from their housing. You must pull out the headlamp assembly to reach the electrical connector for disconnecting it. The current bulb needs removing through counterclockwise rotation. To install the new bulb follow the procedure of twisting it clockwise until it locks into position while replacing high beam bulbs with a red gasket bulb and low beam bulbs with a gray-tip and yellow gasket bulb. Follow this procedure to install the headlamp assembly first reattach the electrical connector then reinstall the assembly using retainer pins that need twisting to secure it. The headlamp requires an inspection before completing the process.

The bulb replacement process starts with turning off the lamp switch while permitting the bulb to cool down. Eye protection should always be worn while you should touch the bulb base only with care because contact with glass or dirt or water must be avoided. After contact with moisture or touching, it is imperative to use alcohol or a suitable degreaser to clean the bulb before wiping it dry. Begin by turning the hood open to access the headlamp retainer pins before properly rotating them before bulb removal. To get to the electrical connector a person should pull out the headlamp assembly and then disconnect the connector. Twist the bulb to the left side in order to remove it. Replacement of high beam bulbs must use another high beam bulb as well as replacement of low beam bulbs with another low beam bulb (with gray tips and yellow gaskets). Illuminate the new bulb by setting its direction clockwise while you secure it in position followed by connector reattachment before you secure the headlamp assembly. Secure the headlamp retainer pins last after their installation.

Start the service of the headlamp bulb by opening the hood and rotating the headlamp retainer pins to remove them. To reach the electrical connector of the headlamp assembly you need to take it out from its position. You must twist off the bulb inside the headlamp assembly in a counterclockwise direction. The installation process requires you to use a high beam bulb with a red gasket for replacement while using a low beam bulb with gray tip and yellow base gasket for the other bulb. To finish the installation insert the bulb into the position and twist it clockwise until it locks securely before connecting the electrical connector. The new headlamp assembly together with its retainer pins should be installed followed by a rotation to lock the pins in position. Check the operation to verify proper system functioning after installation completion.

To change the rear fog lamp bulb, initially, unscrew the screws that secure the lens to the lamp and remove the same. Then, depress the bulb slightly and turn it counterclockwise to the tune of 1/4 turn to pull it out of the socket. For installation, insert the new bulb in the socket, push it in lightly, and turn it 1/4 turn clockwise. Subsequently, attach the lens to the lamp assembly as instructed in Service precautions, Fastener Notice and fix it by putting the screws. Lastly, tighten the screws to 1.5 N.m (13 lb in).

Begin bulb replacement of the headlamp by switching off the lamp and waiting for it to cool down. Handle the bulb strictly at the base while wearing protective eyewear because contact with the glass should be avoided along with moisture and dirt sources. Before unscrewing the headlamp retainer pins you should first open the hood. To remove the headlamp assembly you should pull it out to reach the electrical connector where you must then disconnect it. Crucially rotate the bulb to the left until it comes out freely. Install new bulbs following standard procedure where high beam bulbs replace others with matching characteristics (red gasket) and low beam bulbs should get exchanged with corresponding bulbs (gray tip and yellow gasket). Following installation of the new bulb by a counterclockwise twist to secure it in place you must reconnect the electrical connector and reposition the headlamp assembly. After securing the retainer pins through rotation until locked position it is time to perform an operation checkup. Discard the used bulb safely while storing all halogen bulbs where children cannot access them.

Begin bulb replacement of the rear fog lamp by first removing its lens by unscrewing the retaining screws. First twist the bulb counterclockwise and pull it towards you from the rear fog lamp assembly. Take care with the safety requirements for halogen bulbs during operation. New bulb installation requires users to place it into the rear fog lamp assembly before a clockwise motion reinforces its position. Reinstall the rear fog lamp lens by using the retaining screws to attach it and torque the screws to 2 n.m (18 lb in). The last step requires a check of the rear fog lamp functionality.

The first step to replace a front fog lamp bulb is to switch off the fog lamp. Following the same procedure start by counterclockwise rotation of the bulb socket to detach it from the fog lamp housing. The process starts by detaching the socket from the fog lamp housing after which the bulb can be unwrapped from the socket. To install a new bulb directly place it into the socket while making sure the tabs match the slots of the fog lamp housing. Install the fog lamp socket into the housing and turn it in a clockwise direction until it reaches its full position.

Begin by detaching the screws from the lens then removing the lens to access the rear fog lamp. Begin by carefully pushing the bulb and then turn it to the left by one quarter turn for the bulb to release from its socket. The installation process requires you to insert the bulb inside the socket after gentle pressure and rotating it by 1/4 turn to the clockwise direction. Put the lens onto the lamp assembly before securing it together with the screw installation. Fasten the screws to 1.5 N.m (13 lb in) while adhering to the Fastener Notice in Service Precautions.

The service and repair process of the headlamp bulb requires a user to first place the headlamp switch into off position. Handle halogen bulbs gently because they store gas under pressure which creates risk of bulb breakage. After the bulb has cooled down you should turn off the lamp switch before beginning the replacement. Keep the switch in the off position until the entire bulb replacement process is finished. You should protect your eyes at all times while handling the bulb through its base section only and maintain distance from the glass surface. The bulb needs protection from dirt and moisture while proper disposal of old bulbs must be followed along with keeping all halogen bulbs in locations where children cannot access them. The bulb should not have contact with damp objects or be touched because moisture or oil will cause an explosion when it operates; cleaning the bulb with alcohol or a suitable degreaser then drying it should be done if this happens. You should first perform a headlamp replacement procedure and disconnect the electrical connector before turning the bulb assembly counterclockwise to extract it. Avoid installing a high beam bulb by replacing it with another high beam bulb (with part number 12345) which features a red gasket while using a low beam bulb requires part number 67890 that includes a gray tip and yellow gasket beneath. The new bulb must counterclockwise rotation for assembly installation before reconnecting the electrical connector and following the headlamp replacement process to install the headlamp and ending with a test of the headlamp's functionality.

The initial step to replace a fog lamp bulb requires you to switch off the fog lamp component. The bulb socket can be freed from the fog lamp housing by rotating it counterclockwise. Safely detach the socket from the fog lamp housing followed by removing the bulb from its socket. When installing the new bulb you must push it into the socket after ensuring both socket tabs match with the housing slots of the fog lamp. Follow this procedure to install the socket into the fog lamp housing by rotating it clockwise until it reaches complete seating.

The first step to replace the rear fog lamp bulb involves using a screwdriver to remove the lens screws and then to pull off the lens. Press gently on the bulb before rotating it 1/4 turn to the left for removing it from the socket. After inserting the bulb into its socket take it gently while turning it clockwise by a quarter turn. Attach the lens to the lamp assembly while remembering the fastener caution that prevents vehicle damage and finally tighten the screws to 1.5 Nm (13 lb in).

After turning off the headlamp switch users should disconnect the electrical connector from the headlamp bulb to perform a replacement. Handle halogen bulbs with care since their compressed gas puts them at risk of shattering during improper handling when the lamp control is off and the bulb has cooled down; use protective eyewear, grip the bulb at its base while avoiding touching the glass and maintain them dust and sweating-free before safe disposal and safeguard them from children. The bulb removal process requires turning it counterclockwise until it pops out from the headlamp. The new bulb must be inserted into the headlamp after which a clockwise rotation to lock it into place followed by reattaching the electrical connector to the bulb.

The process to replace a rear fog lamp bulb begins with unfastening the lens screws from the lamp assembly body before removing the lens. Twist the bulb with gentle pressure into the socket and rotate it 1/4 turns to the left to extract it from the socket. Insert the new bulb into the socket then push it with gentle pressure before turning it clockwise by 1/4 turn. Secure the lens to the lamp assembly by fastening screws that should be tightened to 1.5 N.m (13 lb in).

You should begin headlamp bulb replacement on the envoy by turning off the lamp switch and waiting for the bulb to cool down. Users must protect their eyes when handling the bulb and should touch it only through the base to prevent contact with glass surfaces. A clean and dry bulb state alongside proper disposal of used bulbs makes up essential procedures. Begin by opening the hood before taking off the headlamp. First remove the access cover at the headlamp rear section then detach the electrical connector from its socket. To remove the bulb and socket from the housing users should turn both clockwise in the opposite direction. Follow this installation process by attaching the electrical connector to the socket next to attaching and rotating the bulb and socket clockwise until their locking tabs can secure. The last step requires you to put the access cover back before reinstalling the headlamp. The high beam requires a bulb inserted into a black socket while the low beam makes use of a bulb with a gray tip installed into a gray socket.

Before changing the headlamp bulb you need to turn off the lamp switch while waiting for the bulb to cool. Eye protection must be worn during operations while you should only handle the bulb by its base while keeping the glass out of contact. Handle the bulb by its base as you should clean and dry it before disposing of the used bulb through proper methods. Start by opening the hood and rotating both retainer pins at the headlamp before proceeding with removal. You must pull the headlamp assembly to access both the electrical connector and disconnect it. Twist the bulb in the opposite direction to disassemble it. Use steady clockwise turns to set the new bulb while making sure high beam reddish gaskets only replace high beam red gaskets and creating a similar exchange between low beam gray with yellow gaskets bulbs. Place the electrical connector correctly before proceeding to reinstall the headlamp assembly and use the retainer pins to secure it while rotating the pins for locking. Testing the headlamp operation should be the final step in this process.

Begin the fog/driving lamp bulb servicing process by disconnecting the electrical connector but always mind the halogen bulb caution. You should twist the bulb in a counter direction until you can pull it entirely out from the fog lamp housing. You must insert the bulb into the fog lamp assembly before setting it by twisting it clockwise and reattaching the electrical connector.

Before replacing the front fog lamp bulb (Luxury Y91) users need to turn off the lamp switch and wait for the bulb to cool down to avoid glass shattering. Handle the bulb by its base only while using protective eye gear since contact with glass should be avoided and the bulb must remain dry and clean of contaminants. You should disconnect the electrical connector at the back of the fog lamp bulb then rotate it counterclockwise by 45 degrees to remove it. After insertion into the lamp housing the installation of the new fog lamp bulb requires turning it 45 degrees clockwise to lock into position. Before finishing disconnect the electrical connector from the back of the fog lamp bulb and discard the used bulb by maintaining halogen bulbs in areas unreachable to children.

For front fog lamp bulb replacement in the canyon begin by setting the fog lamp switch to off then disconnect the electrical connector. To obtain access to the bulb socket begin by turning the socket counterclockwise toward the fog lamp housing before taking out the socket and bulb from its setting. The installation requires you to position the new bulb inside the socket before aligning the notches on the bulb socket with the corresponding slots in the fog lamp housing. Mount the socket back into the fog lamp housing while turning it clockwise until complete seating is achieved.

Service of the Fog/Driving Lamp Bulb begins with unbolted lens screws from the lamp assembly followed by lens removal. You should insert the bulb and rotate it in a counterclockwise direction by 1/4 turn to separate it from the socket. You should insert the new bulb into its socket then push it gently before rotating it one-quarter turn clockwise for installation. Secure the lens to the lamp assembly but always adhere to the Fastener Notice in Service Precautions listing and complete the installation by using the screws. The screws need to be tightened up to 1.5 N.m which corresponds to 13 lb in.

Before performing a front fog lamp bulb replacement on the canyon the user needs to switch off the fog lamp switch and disconnect the electric connector. The first step to replace the bulb socket requires turning it counterclockwise to free it from the fog lamp housing. Remove the socket from the housing. Remove the bulb from its housing position. The new bulb requires insertion into its matching socket before lining up the socket tabs and slots within the fog lamp housing before installing the socket. You should finish the installation by turning the socket until it reaches complete insertion.

Users should begin the rear fog lamp bulb replacement process by removing the lens through screw removal. The replacement steps require careful handling of halogen bulbs. After removing the retaining screws from the rear fog lamp lens you should proceed to remove the bulb from its assembly by turning it counterclockwise while pulling it out. You must insert the new bulb into the rear fog lamp assembly before securing it by turning the bulb clockwise. Install the rear fog lamp lens through a procedure of reinstalled retaining screws which must be tightened to 2 n.m (18 lb in). The last step involves checking the functioning of the rear fog lamp.

You can change the Headlight Bulb after turning off the lamp switch while waiting for the bulb to cool down. Protect your eyes at all times while you must grip the bulb only at its base to prevent touching the glass. Always maintain the bulb in a clean dry state before following safe procedures for proper bulb disposal. Inspection of the headlamp retainer pins requires rotating them before extracting the pins from their housing. You must pull out the headlamp assembly to reach the electrical connector for disconnecting it. The current bulb needs removing through counterclockwise rotation. To install the new bulb follow the procedure of twisting it clockwise until it locks into position while replacing high beam bulbs with a red gasket bulb and low beam bulbs with a gray-tip and yellow gasket bulb. Follow this procedure to install the headlamp assembly first reattach the electrical connector then reinstall the assembly using retainer pins that need twisting to secure it. The headlamp requires an inspection before completing the process.

Replacing either the headlamp assembly or headlamp bulb (HID) requires you to extract the front grille followed by removing headlamp retainer pins and then drawing out the headlamp assembly in order to disconnect the electrical connector. Access to the headlamp bulbs becomes possible by first removing the rubber cups. Begin by installing the new bulbs before putting on the rubber cups for installation. The electrical connector ties to the lamp assembly first while replacing the lamp assembly back to its position in the vehicle by using headlamp assembly retainer pins before securing the front grille. Be vigilant about the high voltage and current operations of the high intensity discharge system since opening the ballast or arc tube assembly or probing between electrical connectors causes severe shocks and burns. Maintain safe distances between the arc tube and the headlamp housing as well as bulb shield when uninstalling or installing to prevent any damage from occurring.

Starting the replacement of headlamp bulbs requires putting the Ignition Switch to lock position and turning the headlamp switch off. To access the headlamp assembly you need to disconnect both retainers by pulling them outward then disconnect the electrical connectors while taking the assembly out from the vehicle. You should gently push while rotating the bulb 1/4 counterclockwise to remove it from its placement inside the headlamp assembly. To install the new bulb users must push it clockwise 1/4 turn before rotating it back into the headlamp position. After that users should reconnect the headlamp electrical connectors then they can reinstall the assembly back into the vehicle. Place the headlamp assembly retainers into their mountings by pushing them both down and inside the housing. Before handling halogen bulbs always handle them with caution by shielding the glass and maintaining a dry environment free of contaminants.

One should start with disconnecting the electrical connector before proceeding to change the front fog lamp bulb. First twist the bulb counterclockwise before pulling it out from the fog lamp assembly while observing the warning about handling halogen bulbs during service. You must first connect the electrical connector before inserting the new bulb into the fog lamp assembly and turning it clockwise until it is fastened.

Connect the electrical connector to the new headlamp bulb/socket and install it back into the headlamp, rotating it clockwise until fully seated.

Always wear eye protection and handle the bulb only by its base, avoiding contact with the glass while keeping it free from dirt and moisture.

Rotate the headlamp bulb/socket counterclockwise to release it, ensuring to observe the Halogen Bulb Caution.

Reinstall the rubber access cover(s) and connect the electrical connector to the headlamp.

Connect the wire harness to the headlamp bulb.

Always wear eye protection and handle the bulb only by its base, avoiding contact with the glass, dirt, or moisture.

Apply light pressure to the headlamp lens.

Properly dispose of the used bulb and keep halogen bulbs out of children's reach.

Reconnect the electrical connector to the front fog lamp bulb and lower the vehicle.

If necessary, release the headlamp trim tabs and pull the headlamp trim off, removing any adhesive tape.

Install the bulb and socket by rotating them clockwise to lock the retaining tabs into the housing.

Rotate the front fog lamp bulb/socket counterclockwise to release it.

Connect the electrical connector, position the headlamp back onto the upper fascia support, and press it in until the ball stud is fully seated.

Clean the bulb with alcohol or a suitable degreaser and ensure it is dry.

Twist the bulb counterclockwise and pull it out from the fog lamp assembly.

Reinstall the thumb screw at the rear of the headlamp and engage the vertical retainer by sliding it downward until fully seated.

Lift up to release the headlamp retainer.

Begin by placing the bulb into the socket.

Connect the electrical connector to the new headlamp bulb, position the bulb into the headlamp capsule, and twist it clockwise 45 degrees to secure it.

Halogen bulbs contain gas under pressure and can shatter if handled improperly.

Remove the front air deflector.

Halogen bulbs contain gas under pressure and can shatter if handled improperly.

Secure the fog lamp bulb by rotating it 45 degrees clockwise.

Press on the top lever tab and rotate the cover down, ensuring to observe the Halogen Bulb Caution.

Turn the headlamp bulb counterclockwise to disengage it.

Disconnect the electrical connector from the fog lamp bulb.

Install the access cover back onto the rear of the headlamp assembly and reinstall the headlamp.

Remove the headlamp bulb from the headlamp assembly.

Place the fog lamp bulb into the fog lamp housing and turn it clockwise to secure it.

Reinstall the air deflector.

Rotate the bulb socket counterclockwise.

Reconnect the electrical connector.

Reconnect the electrical connector.

Remove the push pin retainers located at the bottom center of the front fascia.

Push and rotate the bulb 1/4 turn counterclockwise.

Reconnect the rear fog lamp electrical connector before lowering the vehicle.

Remove the bulb from the socket.

Position the headlamp bulb/socket at the rear of the headlamp and rotate it clockwise until it is fully seated.

Install the rear fog lamp bulb back into the harness socket and reconnect the rear fog lamp electrical connector.

Install the new bulb into the socket.

Release the brake caliper cooling duct from the front fascia and reposition it.

Disconnect the electrical connector from the fog lamp bulb/socket.

Rotate the headlamp bulb/socket counterclockwise to remove it from the headlamp capsule and disconnect the electrical connector.

Install the new bulb into the socket.

Install the bolts retaining the headlamp, tightening them to 10 Nm (89 lb in).

Reattach the rear fog lamp lens by installing the retaining screws and tighten them to 2 N.m (18 lb in).

Push and rotate the bulb 1/4 turn counterclockwise, then disconnect the electrical connector.

Open the hood and manually raise the headlamp by rotating the headlamp motor/actuator manual control knob counterclockwise.

Lower the vehicle and check and adjust the fog lamp aim as necessary.

Exercise caution as halogen bulbs contain gas under pressure, which can cause shattering; ensure the lamp switch is OFF and the bulb has cooled before handling.

Access the rear fog lamp through the tail lamp opening.

Place the new bulb into the headlamp and rotate it clockwise to secure it.

Rotate the headlamp motor/actuator manual control knob counterclockwise.

Always wear eye protection, handle the bulb only by its base to avoid touching the glass, keep dirt and moisture off the bulb, properly dispose of the used bulb, and keep halogen bulbs out of children's reach.

Remove the rubber access cover and rotate the bulb/socket counterclockwise, observing the Halogen Bulb Caution.

Disconnect the electrical connector from the headlamp and take the headlamp out of the vehicle.

Tighten the screws to 1.5 N.m (13 lb in).

Install the screws to secure the lens, tightening them to 1.5 N.m (13 lb in).

Turn on the fog lamp switch to test the bulb.

Reinstall the radiator air baffle as required and close the hood.

Connect the electrical connector to the bulb/socket and install it by rotating clockwise.

Hold the headlamp in place while pushing downward on the release tabs.

Turn the bulb counterclockwise to remove it from the socket and disconnect the electrical connector from the bulb.

Reattach the rubber access cover, connect the electrical connector to the headlamp, and position the headlamp back into the upper fascia support.

Disconnect the electrical connectors from the lamp sockets and remove the headlamp or park lamp sockets by rotating them counterclockwise.

Reattach the rubber access cover, connect the electrical connector to the headlamp, position the headlamp to the upper fascia support, push the headlamp retainers down until fully seated, reinstall the radiator air baffle, and check and adjust the headlamp aim as necessary before closing the hood.

Remove the rubber access cover from the headlamp.

Ensure to observe the Halogen Bulb Caution.

Carefully remove the headlamp from the slots in the upper fascia support and disconnect the electrical connector.

Remove the bulb by twisting it counterclockwise and pulling it out.

Twist the bulb counterclockwise and pull it out from the fog lamp assembly.

Reconnect the electrical connector and reinstall the headlamp assembly.

Always wear eye protection and handle the bulb only by its base, avoiding contact with the glass.

Disconnect the lamp electrical connectors and take the headlamp assembly out of the vehicle.

Insert the new bulb into the rear fog lamp assembly and twist it clockwise to secure it.

Ensure that the arc tube does not contact the headlamp housing or bulb shield to avoid damage.

Inspect the operation of the headlamp.

Finally, inspect the operation of the rear fog lamp.

Inspect the operation of the rear fog lamp.

Clean the bulb with alcohol or a suitable degreaser and wipe it dry.

Open the hood and remove the headlamp, then take off the access cover from the rear.

Keep the bulb clean and dry, and dispose of the used bulb properly.

Reinstall the access cover at the rear of the headlamp assembly.

Open the hood and remove the access cover from the rear of the headlamp.

Turn the fog lamp switch to the OFF position and disconnect the electrical connector.

Keep the bulb free from dirt and moisture, and dispose of the used bulb properly.

Reach from the engine compartment and twist the bulb counterclockwise.

Turn on the fog lamp switch to test the bulb.

Install the bolts retaining the headlamp, tightening them to 10 N.m (89 lb in), and inspect the headlamps for proper operation before reinstalling the front grille.

Install the socket into the fog lamp housing and rotate it clockwise until it is fully seated.

Insert the new bulb into the socket, ensuring the tabs on the bulb socket align with the slots in the fog lamp housing.

Ensure the headlamp switch is OFF and the ignition switch is in the LOCK position.

Inspect the headlamps for proper operation and reinstall the front grille.

Always wear eye protection and handle the bulb only by its base, avoiding contact with the glass.

Always wear eye protection, handle the bulb only by its base to avoid touching the glass, keep dirt and moisture away from the bulb, properly dispose of the used bulb, and keep halogen bulbs out of children's reach.

Disconnect the electrical connector from the socket, then rotate the bulb and socket counterclockwise to remove them from the housing.

Exercise caution as halogen bulbs contain gas under pressure, which can cause them to shatter if handled improperly. Ensure the lamp switch is OFF and the bulb has cooled before proceeding, wear eye protection, handle the bulb only by its base without touching the glass, keep dirt and moisture away, dispose of the used bulb properly, and keep halogen bulbs out of children's reach.

Gently push in on the bulb and turn it 1/4 turn counterclockwise to remove it from the socket.

Remove the rubber cups to gain access to the headlamp bulbs and take out the bulbs.

Take care to observe the Halogen Bulb Caution in Service Precautions.

Rotate the bulb counterclockwise to disengage it from the headlamp and remove it.

Rotate the bulb counterclockwise to disengage it from the headlamp and remove it.

Pull out the headlamp assembly to access the electrical connector and disconnect it.

Clean it with alcohol or a suitable degreaser and wipe it dry.

Inspect the operation of the rear fog lamp to ensure it is functioning correctly.

Take care to observe the Halogen Bulb Caution in Service Precautions.

Remove the electrical connector, taking care to observe the Halogen Bulb Caution in Service Precautions.