Make sure this part fits

GM 15926026
Lock, Passenger Side

2000-2009 GM

Customer Questions & Expert Answers (55)
GM 15926026 Lock, Passenger Side
GM 15926026 Lock, Passenger Side
  • Part Description
    Latch Assembly-Lift Gate; Door Latch Assembly; Trunk Latch; Door Lock
  • Position
    Passenger Side
  • Replaces
    15757028
  • Manufacturer
    General Motors
Make sure this part fits
$156.61 MSRP: $224.09
You Save: $67.48 (31%)
1
ADD TO CART
  • Vehicle Fitment

    Year Make Model Trim Engine
    2002-2006 Cadillac EscaladeBase8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
    2003-2006 Cadillac Escalade ESVBase8 Cyl 6.0 L GAS
    2002-2006 Cadillac Escalade EXTBase8 Cyl 6.0 L GAS
    2002-2006 Chevrolet Avalanche 1500Base, LS, LT, North Face, On Road Edition, WBH, Z66, Z718 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
    2002-2006 Chevrolet Avalanche 2500Base, LS, LT8 Cyl 8.1 L GAS
    2000-2006 Chevrolet Silverado 1500Base, Hybrid, LS, LT, SS, WT, Z71 Off-Road6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
    2005-2006, 2001-2003 Chevrolet Silverado 1500 HDBase, LS, LT8 Cyl 6.0 L GAS
    2000-2004 Chevrolet Silverado 2500Base, LS, LT, WT8 Cyl 5.3 L GAS, 8 Cyl 6.0 L BI-FUEL, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS
    2001-2006 Chevrolet Silverado 2500 HDBase, LS, LT, WT8 Cyl 6.0 L BI-FUEL, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
    2001-2006 Chevrolet Silverado 3500Base, LS, LT, WT8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
    View More
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 15926026 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 15926026 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should you do after removing the handle bezel for the 2003 Cadillac Escalade? Posted by Customer
    A:
    Lower and support the endgate, then remove the cables from the side panel cable retainer bolts and the bolt holding the latch assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    What is the first step in the installation process for the 2004 Cadillac Escalade ESV? Posted by Customer
    A:
    Attach the actuator cable assembly to the latch.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What should be removed after raising the window glass for the 2004 Cadillac Escalade ESV? Posted by Customer
    A:
    Remove the door trim panel and the water deflector.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What should be connected to the handle retainer clip for the 2002 Cadillac Escalade? Posted by Customer
    A:
    The inside door lock rod.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What should be done after disconnecting the actuator cable assembly for the 2002 Cadillac Escalade? Posted by Customer
    A:
    Remove the latch bolts and the latch itself.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What is the first step in the installation process for the 2004 Cadillac Escalade EXT? Posted by Customer
    A:
    Install the liftgate lock cylinder.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    How do you reconnect the cables for the 2004 Cadillac Escalade ESV? Posted by Customer
    A:
    Connect the cables on each side of the endgate to the side panel cable retainer bolts and engage the linkage rods.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    How do you reconnect the cables for the 2004 Cadillac Escalade EXT? Posted by Customer
    A:
    Connect the cables on each side of the endgate to the side panel cable retainer bolts and engage the linkage rods.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    What is the torque specification for tightening the upper bolt for the 2004 Cadillac Escalade EXT? Posted by Customer
    A:
    Tighten it to 9 N.m (80 lb in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What needs to be removed to disengage the outside handle rod retainer for the 2002 Chevrolet Avalanche 2500? Posted by Customer
    A:
    Remove the rubber plug.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What should you do after removing the handle bezel for the 2002 Chevrolet Avalanche 2500? Posted by Customer
    A:
    Lower and support the endgate, then remove the cables from the side panel cable retainer bolts and the bolt holding the latch assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    What should be done before fully taking the latch out of the door for the 2003 Chevrolet Avalanche 1500? Posted by Customer
    A:
    Remove the latch bolts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What should you do after installing the latch assembly for the 2003 Chevrolet Avalanche 1500? Posted by Customer
    A:
    Connect the cables on each side of the endgate to the side panel cable retainer bolts, engage the linkage rods, raise the endgate, and install the endgate handle bezel, pressing it into place until fully seated.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    What is the first step in the installation process for the 2006 Chevrolet Avalanche 2500? Posted by Customer
    A:
    Attach the actuator cable assembly to the latch.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What should be connected to the handle retainer clip for the 2002 Chevrolet Avalanche 2500? Posted by Customer
    A:
    The inside door lock rod.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What should be removed next after disconnecting the rods for the 2003 Chevrolet Avalanche 1500? Posted by Customer
    A:
    The bolts that retain the door lock actuator to the door.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What should be disconnected after removing the water deflector for the 2003 Chevrolet Avalanche 1500? Posted by Customer
    A:
    Disconnect the inside door lock rod from the handle retainer clip and the manual door lock rod from the door retainer clips.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What is the first step to replace the rear door latch on the cargo door lower for the 2003 Chevrolet Avalanche 1500? Posted by Customer
    A:
    First, remove the bolts that secure the latch assembly to the door.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What should be done after removing the door trim panel for the 2004 Chevrolet Silverado 1500? Posted by Customer
    A:
    Remove the latch retaining bolts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What should you do after installing the latch assembly for the 2004 Chevrolet Silverado 2500? Posted by Customer
    A:
    Install the latch assembly bolts and tighten them to 25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    What are the final steps after connecting all components for the 2004 Chevrolet Silverado 1500? Posted by Customer
    A:
    Install the water deflector and the door trim panel, and inspect the operation of all related components.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What is the first step in the installation process for the 2002 Chevrolet Suburban 2500? Posted by Customer
    A:
    Install the liftgate lock cylinder.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What is the next step after removing the bolts for the 2002 Chevrolet Suburban 2500? Posted by Customer
    A:
    Take out the latch and disconnect the actuator cable assembly from it.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What is the first step to replace the power door lock actuator in the front door for the 2004 Chevrolet Silverado 2500? Posted by Customer
    A:
    First, raise the window glass.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What is the first step for installation for the 2000 Chevrolet Suburban 1500? Posted by Customer
    A:
    Attach the control rods to the assembly and connect the electrical connectors to the door lock actuator if equipped.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What is the next step after removing the bolts for the 2000 Chevrolet Tahoe? Posted by Customer
    A:
    Take out the latch from the door and detach the actuator cable assembly from the latch.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What is the first step for installation of the new latch assembly for the 2004 Chevrolet Tahoe? Posted by Customer
    A:
    Engage the linkage rod to the latch assembly and install the latch assembly to the vehicle, following the Fastener Notice in Service Precautions.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    What is the final step in the process for the 2004 Chevrolet Silverado 3500? Posted by Customer
    A:
    Raise the endgate, install the endgate handle bezel, press it into place until fully seated, and tighten the handle bolts to 25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    What is the first step to replace the tailgate latch for the 2003 Chevrolet Suburban 1500? Posted by Customer
    A:
    Lower the endgate and loosen the handle bolts, then raise the endgate.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    What is the torque specification for tightening the latch assembly bolts for the 2000 Chevrolet Suburban 1500? Posted by Customer
    A:
    Tighten them to 25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Trunk Latch
    Q:
    What should be done after tightening the bottom two bolts for the 2000 Chevrolet Suburban 1500? Posted by Customer
    A:
    Open the door and install the upper bolt, tightening it to 9 N.m (80 lb in) as well.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What is the final step in the process for the 2004 Chevrolet Silverado 1500? Posted by Customer
    A:
    Raise the endgate, install the endgate handle bezel, press it into place until fully seated, and tighten the handle bolts to 25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    What is the first step to replace the power door lock actuator in the front door for the 2004 Chevrolet Silverado 3500? Posted by Customer
    A:
    First, raise the window glass.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What is the torque specification for tightening the latch assembly bolts for the 2000 Chevrolet Tahoe? Posted by Customer
    A:
    Tighten them to 25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Trunk Latch
    Q:
    What should be done after loosening the handle bolts for the 2002 Chevrolet Suburban 2500? Posted by Customer
    A:
    Raise the endgate.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    What is the first step in the installation process for the 2004 Chevrolet Silverado 2500? Posted by Customer
    A:
    Connect the latch rod to the latch, ensuring to adhere to the Fastener Notice in Service Precautions.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What is the first step in the installation process for the 2004 Chevrolet Silverado 3500? Posted by Customer
    A:
    Connect the latch rod to the latch, ensuring to adhere to the Fastener Notice in Service Precautions.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What is the first step to replace the front door lock actuator for the 2002 Chevrolet Tahoe? Posted by Customer
    A:
    Raise the window glass.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What is the final step in the process for the 2004 GMC Sierra 1500? Posted by Customer
    A:
    Reinstall the latch retaining bolts and the door trim panel.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What is the first step to replace the front door lock actuator for the 2001 GMC Yukon XL 1500? Posted by Customer
    A:
    Raise the window glass.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What is the first step to replace the power door lock actuator in the front door for the 2005 GMC Sierra 3500? Posted by Customer
    A:
    First, raise the window glass.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What should be disconnected from the door retainer clips for the 2004 GMC Sierra 1500? Posted by Customer
    A:
    Disconnect the manual door lock rod.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What should be done with the manual door lock rod for the 2004 GMC Yukon? Posted by Customer
    A:
    Disconnect it from the door retainer clips.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What is the purpose of closing the door during installation for the 2004 GMC Yukon? Posted by Customer
    A:
    To allow the latch assembly to self-adjust.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What is the next step after installing the latch for the 2005 GMC Sierra 3500? Posted by Customer
    A:
    Install the latch retaining bolts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What is the next step after removing the bolts for the 2004 GMC Yukon XL 2500? Posted by Customer
    A:
    Take out the latch and disconnect the actuator cable assembly from it.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What should you do after removing the handle bezel for the 2004 GMC Sierra 1500? Posted by Customer
    A:
    Lower and support the endgate, then remove the cables from the side panel cable retainer bolts and the bolt holding the latch assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    What is the first step to replace the rear side door lock actuator for the 2001 GMC Yukon XL 1500? Posted by Customer
    A:
    Raise the window.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What is the torque specification for tightening the latch assembly bolts for the 2001 GMC Yukon XL 1500? Posted by Customer
    A:
    Tighten them to 25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Trunk Latch
    Q:
    How do you remove the handle bezel for the 2004 GMC Yukon XL 2500? Posted by Customer
    A:
    Gently pry on the upper retainer tabs to remove the handle bezel and disengage the linkage rods.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    What should be done after removing the bolts for the 2001 GMC Yukon XL 1500? Posted by Customer
    A:
    Disconnect the electrical connector if necessary, and take out the actuator cable assembly from the latch.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Latch Assembly
    Q:
    What should you do after installing the latch assembly for the 2005 GMC Sierra 3500? Posted by Customer
    A:
    Install the latch assembly bolts and tighten them to 25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    What is the first step for installation of the new latch assembly for the 2004 GMC Yukon? Posted by Customer
    A:
    Engage the linkage rod to the latch assembly and install the latch assembly to the vehicle, following the Fastener Notice in Service Precautions.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Tailgate Latch
    Q:
    What should be connected to the lock assembly after the manual door lock for the 2004 GMC Yukon XL 2500? Posted by Customer
    A:
    Connect the control rod for the inside door handle to the lock assembly and the inside door lock rod to the handle retainer clip.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Lock, Passenger Side 15926026 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 15926026 Lock, Passenger Side is available in the market under the name GM Door Lock, Door Lock Actuator, Tailgate Latch, Tailgate Lock, Trunk Latch, Door Latch Assembly. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 15926026 Lock, Passenger Side fits certain Chevrolet Tahoe, Silverado 1500, Silverado 2500 HD models, as well as GMC Sierra 1500, Yukon, Sierra 2500 HD. Additionally, it is compatible with Cadillac Escalade, Escalade ESV, Escalade EXT and Hummer H2 models.
The original GM component designated by manufacturer part number 15926026 maintains top performance when functioning as the Latch Assembly-Lift Gate; Door Latch Assembly; Trunk Latch; Door Lock unit at its Passenger Side. The component 15926026 is constructed from durable material and its dimensions span 6.4 x 4.3 x 4.3 inches while weighing 1.10 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Latch; Latch, End Gate Lock; Latch, Door Lock. The part 15926026 has available replacement options 15757028. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.